Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
To protect the wiring, wrap adhesive tape around them where they lie against metal parts. • Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. • Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. • Do not shorten any leads. If you do, the protection circuit may fail to work when it should. • Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. • When replacing fuse, be sure to use only fuse of the rating prescribed on this unit. • Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right © speaker leads are common. • The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. Speakers connected to this unit must be highpower types with minimum rating of 45 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke or becoming damaged. When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal. (Max. 300 mA 12 V DC.) If the car features a glass antenna, connect to the antenna booster power supply terminal. When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction. To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated. If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig. 4) ACC position No ACC position Fig. 4 Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. Antenna jack [ Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Black (ground) To vehicle (metal) body. Fuse resistor Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. Perform these connections when using a different amp (sold separately). Fig. 5 Установка Примечание: • Перед тем как установить устройство окончательно, подсоедините временно все провода и убедитесь, что все контакты в порядке, и что устройство и система работают надлежащим образом. • Для обеспечения правильности установки используйте лишь детали, поставляемые в комплекте с устройством. Использование посторонних деталей может привести к возникновению неисправностей. • Если для установки требуется сверление отверстий в корпусе автомобиля или же какие-либо другие его модификации, проконсультируйтесь по данному вопросу ближайшим к Вам дилером. • Установите устройство в таком месте, чтобы оно не мешало водителю и не смогло травмировать пассажиров при резком торможении, как то, например, при аварийной остановке. • При перегреве полупроводниковый лазер может выйти из строя, поэтому не устанавливайте изделие в местах с потенциально высокой температурой, например, у выпускной трубы обогревателя. Если угол установки относительно горизонтали будет превышать 60 градусов, то устройство будет работать возможно не самым лучшим образом. (Рис. 1) Рис. 1 <РУССКИИ> Установка с резиновым вкладышем Приборная панель Держатель Вставив держатель в приборную панель, выберите затем шпонки, соответствующие толщине материала приборной панели, и загните их. (При помощи верхней и нижней шпонок установите изделие как можно более плотно. Чтобы зафиксировать, загните...