Stimmen - 6, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Repeat the operation until the desired station is received. Local Seek Mode: If the automatic tuning stops too frequently, press (sens) repeatedly until “LOCAL-ON” appears in the display. )fm iLOCAL- ON ini Only the stations with relatively strong signals will be tuned in. To cancel the local seek mode, press (SENS) twice when receiving FM. Note When receiving AM, to cancel the local seek mode, press (sens) (“LOCAL-OFF"appears). Tip If you know the frequency of the station you want to listen to, press and hold ( seek) (+) or ( seek) (-) to locate the approximate frequency, then press (seek) (+) or (seek) (-) repeatedly to fine adjust to the desired frequency (manual tuning). If FM stereo reception is poor — Monaural Mode During radio reception, press (sens) repeatedly until “MONO-ON” appears in the display. )fm I MONO- ON Ini The sound improves, but becomes monaural (“ST” disappears). To return to normal radio reception mode, press (SENS) (“MONO-OFF” appears). Storing only the desired stations You can manually preset the desired stations on any chosen number button. 1 Press (source) repeatedly to select the radio. 2 Press (mode) repeatedly to select the band. 3 Press (seek) (+) or (seek) (-) to tune in the station that you want to store. 4 Press the desired number button (CD to (6)) for 2 seconds until “MEM” appears. The number button indication appears in the display. Note If you try to store another station on the same number button, the previously stored station will be erased. Other Functions You can also control the unit with a rotary commander (optional). Using the rotary commander First, attach the appropriate label depending on how you want to mount the rotary commander. The rotary commander works by pressing buttons and/or rotating controls. By pressing buttons to adjust the volume. Press To (SOURCE) Change the source (Radio/CD)/Power on (MODE) Change radio band (ATT) Attenuate the sound C°EE)*1 Stop playback or radio reception/Power off (SEL) Adjust and select (DSPL) Change the display item 14 By rotating the control Changing the operative direction The operative direction of controls is factory-set as shown below. Rotate and release to: - Skip tracks. If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. To continuously skip tracks, rotate once and rotate again within 1 second and hold the control. - Tune in stations automatically. Rotate, hold, and release to: - Fast-forward/reverse a track. - Find a station manually. By pushing in and rotating the control Push in and rotate the control to: - Receive preset stations. - Change albums*2. *1 If your car has no ACC (accessory) position on the ignition key switch, after turning off the ignition, be sure to press and hold (off) until the display disappears. *2 Available only when an MP3 file is played. When an MP3 file is played, you can select an album using the rotary commander. To Do this Skip albums Push in and rotate [once for -Album selection each album] the control. Press (sel) for 2 seconds while pushing the VOL control. To continuously skip albums, push in and rotate (and hold) the control. 15 Adjusting the sound characteristics Changing the sound and display settings You can adjust the balance, fader, low pass filter and subwoofer volume. 1 Press (sel) repeatedly until “BAL,” “FAD,” “LPF” or “SUB” appears. Each time you press (SEL), the item changes as follows: LOW*1 t MID*1 t HI*1 t BAL (left-right) t FAD (front-rear) t LPF (low pass filter)*2*3 t SUB (subwoofer volume)*2*4 *1 When EQ3 is activated (page 17). *2 When “SUB" is selected (page 16). *3 The cut off frequency is adjustable to 78 Hz, 125 Hz or OFF. *4 The volume level is adjustable between -10 and +10 steps. (Below-10, “ATT" is displayed.) 2 Press the volume +/- button to adjust the selected item. Note Adjust within 3 seconds after selecting the item. — Menu The following items can be set: Set up • REAR/SUB*1 — to switch the audio output REAR or SUB. - Select “REAR” to output to a power amplifier. - Select “SUB” to output to a subwoofer. • A.SCRL (Auto Scroll)*2 (page 12) • DEMO*1 — to turn the demonstration display on or off. - Select “ON” to activate the demonstration display (The demonstration starts about 10 seconds after the unit is turned off). - Select “OFF” to deactivate the demonstration display. • BEEP — to turn the beeps on or off. • DIM — to change the brightness of the display. - Select “ON” to dim the display. - Select “OFF” to deactivate the Dimmer. Quickly attenuating the sound Press (att). After “ATT-ON” momentarily appears, “ATT” appears in the display. To restore the previous volume level, press (ATT) again. Tip When the interface cable of a car telephone is connected to the ATT lead, the unit decreases the volume automatically when a telephone call comes in (Telephone ATT function). 16 Switc...