Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Tip • You can also complete the reconnection on your device. 20 EN Play audio from a Bluetooth device If the connected Bluetooth device suppor ts Advanced Audio Distribution Profile (A2DP), you can listen to tracks that are stored on the device through the system. If the device also suppor ts Audio Video Remote Control Profile (AVRCP) profile, you can control play on the system or with its remote control. 1 Play a track on the connected device. 2 Press AS/SOURCE repeatedly to switch the source to [BT AUDIO]. » Play star ts automatically. • To pause or resume play, press . • To skip to the previous or next track, press / . Note • If the connected device does not suppor t the AVRCP profile, control play on the connected device. Make a call Note • Keep the Bluetooth connection active between the system and your mobile phone. Call a number On your mobile phone, call a number. » [CALLING] is displayed. Redial the last called number 1 Press . » [REDIAL] is displayed. 2 Press to confirm. » [CALLING] is displayed. Pick up an incoming call When the system receives an incoming call, the phone number or [PHONE IN] is displayed. Press to answer the call. Reject an incoming call Press and hold until [END] is displayed. End a call To end an on-going call, press . Transfer a call to mobile phone By default, the voice comes from the loudspeakers during a call. 1 Press and hold until [TRANSFER] is displayed. » The loudspeakers are muted, and the voice comes from your mobile phone only. 2 Take up your mobile phone for the conversation. EN 21 22 EN 9 Listen to an external player You can use the system to amplify the audio input from an external player, for example, MP3 player. 1 Switch the source to [MP3--LINK]. 2 Connect an MP3 link cable to • the MP3-LINK socket on the system, and • the audio output socket (usually the headphone socket) on the external player. 3 Play the external player. MP3-LINK 10 Adjust sound The following operations are applicable to all suppor ted media. Button Function Rotate to increase or decrease the volume level. Press to mute or restore sound. Press to enable or disable the maximum volume. Press and hold to enable or disable the Dynamic Bass Boost (DBB) effect. Press repeatedly to select a sound equalizer. 1Press and hold to activate the setup of customized sound equalizer. 2Press repeatedly to select an option: [BAS] (bass), [TRE] (treble), [BAL] (balance), or [FAD] (fader). 3Rotate to adjust the setting. EN 23 11 Additional information Reset the system If the system works abnormally, reset the system to factor y default settings. 1 Detach the front panel. 2 Press the RESET button with the tip of a ball-point pen or toothpick. » All settings are reset to factor y default. Replace the fuse If there is no power, check the fuse and replace it if it is damaged. 1 Check the electric connection. 2 Remove the damaged fuse from the rear panel. 3 Inser t a new fuse with the same specifications (15 A). REAR L R Note • If the fuse gets damaged immediately after it is replaced, an internal malfunction may occur. In such case, consult your Philips retailer. 24 EN 12 Product information Note • Specifications are subject to change without prior notice. General Power supply 12 V DC (11 V - 16 V), negative ground Fuse 15 A Suitable speaker 4 - 8 impedance Maximum power output 50 W x 4 channels Continuous power 22 W x 4 RMS output (4 10% T.H.D.) Pre-Amp output voltage 2.0 V Aux-in level 500 mV Radio Frequency range 87.5 - 108.0 MHz -FM (100kHz per step in auto search and 50kHz per step in manual search) Usable sensitivity - FM (S/N = 20 dB) 8 .V Frequency range - 522 - 1620 KHz (9 kHz) AM(MW) 530 - 1710 kHz (10 Bluetooth Output Class 2 power Frequency band 2.4000 GHz - 2.4835 GHz ISM Band Range 3 meters(free space) Standard Bluetooth 2.0 specification kHz) Usable sensitivity - AM(MW) (S/N = 20 dB) 30 .V EN 25 13 Troubleshooting Warning • Never remove the casing of this product. To keep the warranty valid, never tr y to repair the product yourself. If you encounter problems when using this product, check the following points before requesting ser vice. If the problem remains unsolved, go to the Philips Web page (philips.com/suppor t). When you contact Philips, make sure that the product is nearby and the model number and serial number are available. General No power or no sound • The power supply from car batter y is cut off, or the car batter y runs out of energy. Power the system with car batter y. • Car engine is not on.Turn the car engine on. • Cable is not correctly connected. Check connections. • The fuse is burnt. Replace the fuse. • Volume is too low. Adjust volume. • If the above solutions do not work, press the RESET button. • Make sure that the current track is in a compatible format. Noise in broadcasts • Signals are too weak. Select other stations with stronger signals. • Check the connection of the car antenna. Preset stations are erased. • Batter y cable is not correctly connected. Connect the ...