Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Fotos und technische Daten Philips CMD305A/05 |
Anleitung Zusammenfassung
••Make sure that all loose leads are insulated with electrical tape. ••Make sure that the leads do not get caught under screws iron parts that will move (e.g. seat rail). ••Make sure that all ground (earth) leads are run to a common ground (earth) point. ••Use only the supplied mounting hardware for a safe and secure installation. ••Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. ••When you connect other devices to this system, make sure that the rating of the car circuit is higher than the total fuse value of all the connected devices. ••Never connect speaker wires to the metal body or chassis of the car. ••Never connect speaker wires with stripes to one another. Connect wires Caution ••Make sure that all loose leads are insulated with electrical tape. 1 Check the car's wiring carefully, and then connect them to the supplied ISO wires. abcdefgh Connector Connect to 1 Yellow wire The +12V car battery which is live at all times 2 Blue/White wire The electric antenna control lead or power supply lead of the antenna booster. If there is no electric antenna or antenna booster, or it is manually operated telescopic antenna, it is unnecessary to connect this lead. 3 Black wire A metal surface of the car. Connect the black ground (earth) lead before connecting the yellow and red power supply leads. EN Connector Connect to 4 Red wire The +12V power terminal which is live in the accessory (ACC) position of the ignition switch. If there is no accessory position, connect to the +12V car battery terminal that is always live. Make sure that the black ground (earth) lead is connected to a metal surface of the car first. 5 Green and green/black wires Left speaker (rear) 6 White and white/black wires Left speaker (front) 7 Gray and gray/black wires Right speaker (front) 8 Purple and purple/black wires Right speaker (rear) 2 Connect the other end of the supplied standard connector to the car audio system. abcdefgh ........................................ Connector Connect to 1 ANTENNA Antenna for radio 2 External Mic An external microphone for phone call 3 SUBWOOFER (Socket) Subwoofer 4 REAR LINE OUT L (Socket) Rear left speaker 5 REAR LINE OUT R (Socket) Rear right speaker 6 OE REMOTE (Brown) OE remote 7 FRONT LINE OUT L Front left speaker 8 FRONT LINE OUT R Front right speaker Tip ••The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Be sure to make proper connections to prevent damage to the system. Mount into the dashboard Note ••If your car has no an on-board drive or navigation computer, disconnect the negative terminal of the car battery. ••If your car has an on-board drive or navigation computer, the computer may lose its memory when you disconnect the car battery. ••If the car battery is not disconnected, to avoid short- circuit, make sure that bare wires do not touch each other. EN 1 Make sure that the car dashboard opening is within these measurements. 183 mm53mm5mm 2 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve. Note ••If the system is not fixed by sleeve but by the supplied screws, skip this step. 183 mm53.5 mm 3 Place the supplied rubber cushion over the end of the mounting bolt. 4 Slide the system into the dashboard until you hear a "click". 5 Attach the trim plate. 6 Reconnect the negative terminal of the car battery. EN 4 Get started Power on Press . »»[WELCOME] scrolls. • To power off the system, press and hold until [GOODBYE] is displayed. Change system settings 1 Press and hold to access the system menu. 2 Press repeatedly to select an option. • [BT RECON]/[DISCONNECTED] • [RDS] • [PTY >] • [RDS AF] • [RDS TA] • [TP STORE] • [RDS REG] • [RDS CT] • [STORE >] • [AREA] • [LOCAL] • [CLOCK] • [CLOCK 12H] • [BEEP] • [BKO] • [DIMMER] • [DEMO] 3 Rotate to select a setting. • To exit the setting, press . Set the clock 1 Press and hold to access the system menu. 2 Press repeatedly until [CLOCK] and the current time are displayed. »»If the clock is not set before, [--:--] is displayed. 3 Rotate to set the hour. 4 Press to confirm. 5 Rotate to set the minute. 6 Press to confirm. Set the clock format 1 Press and hold to access the system menu. 2 Press repeatedly until [CLOCK 12H]or [CLOCK 24H] is displayed. 3 Rotate to select a setting. • [CLOCK 12H]: 12-hour time format • [CLOCK 24H]: 24-hour time format Display the clock Press to display the clock. • To exit, press any button. Select a source Note ••When all other sources are unavailable, the system switches the source to [RADIO] automatically. Press repeatedly to select a source. • [RADIO]: FM/MW radio • [AUDIO-IN]: the audio that is transferred through the AUDIO-IN socket • [BT AUDIO]: the audio that is transferred from a Bluetooth device • [USB]: When a USB storage device is connected and recognized, you can select this source to play audio files that are stored on it. EN 5 Listen to radio Select a radio region You can select a radio region th...