Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Caution • This unit is designed for negative ground (ear th) 12 V DC operation only. • Always install this unit in the car dashboard. Other locations can be dangerous as the rearof the unit heats up during use. • To avoid shor t-circuit: before you connect, ensure that the ignition is off. • Ensure that you connect the yellow and red power supply leads after all other leads are connected. • Ensure that all loose leads are insulated with electrical tape. • Ensure that the leads do not get caught under screws orin par ts that will move (e.g. seat rail). • Ensure that all ground (ear th) leads are run to a common ground (ear th) point. • Use only the supplied mounting hardware for a safe and secure installation. • Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. 11 Connect wires: ISO connectors Caution Ensure that all loose leads • are insulated with electrical tape. 1 Pull out the ISO connectors from the car dashboard and connect them to the bigger end of the supplied standard connector. 2 Connect the other end of supplied standard connector to the unit. 3 Do the other connections, if applicable. Note on the power supply lead (yellow) • When you connect other devices to this apparatus, ensure that the rating of the car circuit is higher than the total fuse value of all the connected devices. Notes on speaker connection • Never connect speaker wires to the metal body or chassis of the car. • Never connect speaker wires with stripes to one another. Overview of parts These are the supplied parts needed to connect and install this unit. a In-car audio system and sleeve b Standard connector c Screws (4 pieces) d Disassembly tools e Rubber cushion f Front panel g Trim plate 1 2 3 4 5 6 7 English EN ANTENNA Connector Connect to FRONT LINE OUT R FRONT LINE OUT L REAR LINE OUT L REAR LINE OUT R SUB OUT 1 Black wire A metal surface of the car First connect the black Connect wires: without ISO ground (ear th) lead, then connectors connect the yellow and red power supply leads. Caution 2 Yellow wire The +12V car battery which is live at all times. Ensure that all loose leads are insulated with • electrical tape. 3 Blue wire Motor/electric antenna relay control lead/Amplifier 1 Cut off the bigger end of the supplied standard connector. 4 Red wire relay control lead The +12V power terminal which is live in the accessory (ACC) position of the ignition switch If there is no accessory position, connect to the +12V car batter y terminal that is always live. Be sure to connect the black ground (ear th) lead to a metal sur face of the car first. 5 Green and Left speaker (Rear) 2 Check the car’s wiring carefully, then green/black wires connect them to the standard connector. 6 White and Left speaker (Front) white/black wires 7 Gray and Right speaker (Front) gray/black wires 13 If the car battery i • s not disconnected, to avoid short-circuit, ensure that bare wires do not touch each other. 2 Remove the two screws on the top of the unit. 3 Remove the mounting sleeve with the supplied disassembly tools. 4 Ensure that car dashboard opening is within these measurements: 183 mm 53mm 5mm 8 Purple and purple/ black wires Right speaker (Rear) 3 Connect the supplied standard connector to the unit. 4 Do the other connections, if applicable. Mount in the dashboard 1 If the car does not have an on-board drive or navigation computer, disconnect the negative terminal of the car battery. • If you disconnect the car battery in a car that has an on-board drive or navigation computer, the computer may lose its memory. ANTENNA FRONT LINE OUT R FRONT LINE OUT L REAR LINE OUT L REAR LINE OUT R SUB OUT English EN 14 5 Push the front side of the panel backward to the main unit a “click” is heard. Install remote control battery Caution Risk of explosion! K • eep batteries away from heat, sunshine or fire. Never discard batteries in fire. • Risk of decreased battery life! Never mix different brands or types of batteries. • Risk of product damage! When the remote control is not used for long periods, remove the batteries. • Perchlorate Material - special handling may apply. See perchlorate. For first-time use: 1 Remove the protective tab to activate the remote control battery. To replace the remote control battery: 1 Open the battery compartment. 2 Insert 1 CR2025 battery with correct polarity (+/-) as indicated. 3 Close the battery compartment. 5 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve. Note • Skip this step if the unit is not fixed by sleeve but by supplied screws. 6 Place the supplied rubber cushion over the end of the mounting bolt. 7 Slide the unit into the dashboard until you hear a click sound. 8 Reconnect the negative terminal of the car battery. Attach the front panel 1 Attach the trim plate to the main unit. 2 Insert the right side of the panel in the chassis until it is correctly engaged. 3 Push the left side of the panel ...