Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Kenwood Dateigröße: 4.19 mb Dateiname: Unterrichtssprache:

Displaying the Audio Control 1 screen Audio Control 1 screen Displaying the Audio Control 2 screen Audio Control 2 screen -1 1 2 3 4 6 97 5 4 5 6 7 8 Menu Flat BMS AMP Bass BMS AMP FREQ Normal Audio Control 2 Low 1210111011 1 Returns to the Control screen of the previous source. 2 Calls the Setup Menu. (page 49) 3 Calls the Sound Effects Menu. 4 Adjusts the right and left volume balance. 5 Adjusts the front and rear volume balance. 6 Adjusts the volume of the present source based on the difference level of original volume. • If you have increased the volume first, then reduced the volume using the "Vol. Offset", the sound generated if you suddenly switch to another source may be extremely loud. 7 Adjusts the subwoofer volume. 8 Turns the Loudness control function On or Off. If turned "On", high and low tones are automatically enhanced during low volume. ( On) 9 Displays the Audio Control 2 screen. p Adjusts the bass boost of the B.M.S power amplifier (optional accessory). • You may not set some models of power amp boost to "+18". See the catalog or instruction manual of power amplifier. q Sets the center frequency of bass boost you have set for "AMP Bass". If you set the center frequency to "Low", it will be dropped approximately 20% to 30%. w Displays the Audio Control 1 screen. English | 71 Equalizer You can set up the equalizer. Displaying the Equalizer screen Equalizer screen Menu Natural System Q Tone Equalizer OnSystem Q-EX 1 2 3 4 5 6 4 1 Returns to the Control screen of the previous source. 2 Calls the Setup Menu. (page 49) 3 Calls the Sound Effects Menu. 4 Selects an equalizer curve type. You can select any of the following equalizer curves. • "Natural" • "Rock" • "Pops" • "Easy" • "Top40" • "Jazz" 5 Selects items to be adjusted for tone curve setup. If turned "Off", only Level can be setup for tone curves. 6 Displays the Tone curve setup screen. (page 73) 72 | English Sound Effects Menu Sound Effects Menu Tone curve setup 4 Set a level Level You can set a Tone curve. 1 Display the Tone setup screen 5 Set a Q factor Tone Q Factor Tone setup screen 6 5 4 3 2 1 You can set it up only when Bass or Middle is adjusted. 6 Close the Tone setup screen 1 Bass adjustment items are displayed. 2 Middle adjustment items are displayed. 3 Treble adjustment items are displayed. 4 Bass DC Extend settings If turned "On", it extends the bass center frequency to the low register by approximately 20%. 5 Tone curve becomes flat. 6 Returns to the Equalizer screen. • Tone curve can be set for each source. 2 Select a frequency band you wish to adjust You can adjust the following frequency bands. Bass: 40, 50, 60, 70, 80, 100, 120, 150 Hz Middle: 500, 1k, 1.5k, 2k Hz Treble: 10k, 12.5k, 15k, 17.5k Hz 3 Set a center frequency FREQ English | 73 Sound Effects Menu Sound Effects Menu Zone Control You can set the front and rear audio source. Displaying the Zone Control screen Zone Control screen 1 2 3 4 55 6 7 1 Returns to the Control screen of the previous source. 2 Calls the Setup Menu. (page 49) 3 Calls the Sound Effects Menu. 4 Turns the Zone Function (that sets different source sounds for front and rear speakers) On or Off. When turned On, and are shown. 5 Sets the front and rear audio source separately. (This button appears when the Zone function is On.) • When the rear speaker sound is switched, the audio source that is output at the AV OUTPUT terminal is also switched to the same source. However, if you have set the "Area" to "Reverse", the audio source that is output at the AV OUTPUT terminal is switched depending on the front sound source. 6 Switches the front and rear audio sources. (This button appears when the Zone function is On.) Use "Reverse" to change over the front and rear audio sources. 7 Adjusts the volume of the rear channel. (This button appears when the Zone function is On.) • There are following limitations when zone function is set to "On". -There is no output from the subwoofer or center. -

Herunterladen

Geben Sie zwei Ziffern: