Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
•To reverse the scan direction, turn the Tuning control. •To quit the • When the tone and the identified 3 Press [MENU] to program the identified tone frequency in place of the current press any other key to exit the Tone Frequency ID Scan. •Turn the Tuning control while the identified tone frequency is blinking to resume scanning. 4 Press any key other than [MENU] to exit Menu Mode. Note: . Some repeaters do not re-transmit the access tone in the download signal. In this case, check the other station’s uplink signal to detect the repeater access tone. . The transceiver continues to check the Weather Alert Channel and Priority Channel during Tone Frequency ID Scan. 6 27 MEMORY CHANNELS 7 MEMORY CHANNELS 7 In Memory Channels, related data that need to reprogram You can quickly recall a programmed A total of 200 Memory Channels Memory Name function) are frequencies, modes, and other NUMBER OF MEMORY CHANNELS The transceiver must be configured to either Memory Channels without using the Memory function or 100 Memory Channels with the Memory Name function (default). To change the Memory Channel capacity: 1 Press [F] , [MENU] and turn the Tuning control to select Menu No. 15 (M.CH). 2 Press [MENU] and turn the Tuning control to select either “100” (default) or “200”. 3 Press [MENU] . • “SURE ?” appears. 4 Press [MENU] to accept or press cancel. Note: . If you change the Memory Channel 100 channels after having stored Memory Channel data in channels . If you change the Memory Channel 200 channels after storing Memory Names Memory Name data will be erased. SIMPLEX & REPEATER OR ODD-SPLIT MEMORY CHANNEL? You can use each Memory Channel as a simplex repeater channel or an odd-split channel. Store only 1 frequency to use as a simplex & repeater channel or separate frequencies to use as an odd-split channel. Select either application for each channel depending on the operations you have in mind. Simplex & repeater channels allow: • Simplex frequency operation • Repeater operation with a standard offset (if an offset direction is stored) Odd-split channels allow: • Repeater operation with a non-standard offset Note: Not only can you store data in Memory Channels, but you can also overwrite existing data with new data. 28 The data Note: Channel: . Memory Channel Memory (L0/U0 Weather Alert Channel (AL). . Tone, CTCSS, and DCS setting up the Weather Alert Channel (AL). 29 retemaraP& xelpmiSretaepeRtilpS- ddOycneuqerfevieceRseYseYycneuqerftimsnarTseYycneuqerfenoTseYseYNOenoTseYseYycneuqerfSSCTCseYseYNOSSCTCseYseYedocSCDseYseYNOSCD seYseYnoitceridtesffOseYA/ NycneuqerftesffOseYA/ NNOesreveRseYA/ NezispetsycneuqerFseYseYMFdnabworraNseYseYtfihStaeBseYseYtuokcollennahCyromeMseYseYemanlennahCyromeMseYseYYes: Can be stored in memory. N/A: Cannot be stored in memory. STORING SIMPLEX FREQUENCIES REPEATER FREQUENCIES 1 Press [VFO] . 2 Turn the Tuning control to select your desired frequency. •You can also directly enter a desired frequency using the keypad {page 13}. 3 If storing a standard repeater frequency, select the following data: •Offset direction {page 23} •Tone function, if necessary {page 24} • CTCSS/ DCS function, if necessary {pages 46, 48} If storing a simplex frequency, you may select other related data (CTCSS or DCS settings, etc.). 4 Press [F] . • A Memory Channel number appears and blinks. •“ ” appears if the channel contains data. 7 7 • Memory {page 43}, AL (Weather Alert) {page models only) 5 Turn the Tuning control or press [UP] / [DWN] to select the Memory store the data. 6 Press [MR] to store the data to the STORING ODD-SPLIT REPEATER FREQUENCIES Some repeaters use a pair of reception frequencies with a non-standard offset. If you store 2 separate frequencies in a Memory Channel, operate on those repeaters without programming offset frequency and direction. 1 Store the desired reception frequency and related data by following steps 1 to 6 given for simplex or standard repeater frequencies {page 29}. 2 Turn the Tuning control or press Mic [UP] / [DWN] to select your desired transmission frequency. 3 Press [F] . 4 Turn the Tuning control or press Mic [UP] / [DWN] to select the pre-programmed reception Memory Channel in which you want to store the data. 5 Press [MR] (1s) . • The transmission frequency is stored in the Memory Channel. Note: . When you recall an odd-split Memory on the display. To confirm the transmission frequency, press [REV] . . Transmit offset status and reverse status are not stored odd-split Memory Channels. RECALLING A MEMORY CHANNEL USING THE TUNING CONTROL 1 Press [MR] to enter Memory Recall mode. • The Memory Channel last used is recalled. 2 Turn the Tuning control to select your desired Memory Channel. •You cannot recall an empty Memory Channel. •To restore VFO mode, press [VFO] . 30 USING THE MICROPHONE KEYPAD USING THE MICROPHONE KEYPAD 1 Press [MR] to enter Memory Recall 2 Press the microphone key function. 3 Enter the channel number using keypad. • For single-digit channel numbers, ...
Dieses Handbuch ist für folgende Modelle:Car-Receiver - TM-271A (2 mb)