Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Kenwood Dateigröße: 1.91 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Car-Receiver - KDC-W6531 (1.95 mb)

Car-Receiver - KDC-W6531 (1.94 mb)

Car-Receiver - KDC-W6531 (1.89 mb)

Car-Receiver - KDC-W6531 (1.91 mb)

• The setup Security Code can be done when the (page 31) is set as OFF. Control knob RDS indicator NEWS indicator English | 25 • When the Security Code function is activated, it can’t be released. Note, your Security Code is the 4 digit number entered in your "Car Audio Passport" in this package. 1 Enter Standby Press the [SRC] button. Select the "STANDBY" display. 2 Enter Menu mode Press the [MENU] button for at least 1 second. When "MENU" is displayed, "SECURITY" is displayed. 3 Enter Security Code mode Press the Control knob for at least 1 second. When "ENTER" is displayed, "CODE" is displayed. 4 Select the digits to enter Push the Control knob to [4] or [.]. 5 Select the Security Code numbers Push the Control knob to [FM] or [AM]. 6 Repeat steps 4 and 5, and complete the Security Code. 7 Confirm the Security Code Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is displayed. 8 Do the step 4 through 7 step operation, and reenter the security code. "APPROVED" is displayed. The Security Code function activates. • If you enter a Code different from your Security Code, you have to start over from step 4. Press the Reset button and when it’s removed from the battery power source 1 Turn the power ON. 2 Do the step 4 through 7 step operation, and reenter the security code. "APPROVED" is displayed. The unit can be used. • If an incorrect code is input, "WAITING" is displayed, and the input prohibited time shown below is generated. After the input prohibited time lapses, "CODE" is displayed, and input can be done. Number of times the incorrect code was input Input prohibited time 1 — 2 5 minutes 3 1 hour 4 24 hours In Standby mode Touch Sensor Tone Setting the operation check sound (beep sound) ON/OFF. Display Setting "BEEP ON" Beep is heard. "BEEP OFF" Beep canceled. In Standby mode Manual Clock Adjustment • This adjustment can be done when the (page 26) is set as OFF. 1 Select Clock Adjustment mode Push the Control knob to [FM] or [AM]. Select the "CLK ADJ" display. 2 Enter Clock Adjust mode Press the Control knob for at least 1 second. The clock display blinks. 3 Adjust the hours Push the Control knob to [FM] or [AM]. Adjust the minutes Push the Control knob to [4] or [.]. 4 Exit Clock adjustment mode Press the [MENU] button. 26 | English Menu system In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit’s clock. Display Setting "SYNC ON" Synchronizes the time. "SYNC OFF" Adjust the time manually. • It takes 3 to 4 minutes to synchronize the clock. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF. In Standby mode Selectable Illumination Selecting the button illumination color as green or red. Display Setting "KEY RED" The illumination color is red. "KEY GRN" The illumination color is green. In Standby mode Dimmer Dimming this unit’s display automatically when the vehicle light switch is turned ON. Display Setting "DIM ON" The display dims. "DIM OFF" The display doesn’t dim. In Standby mode Switching preout Switching the preout between the rear and subwoofer. (In subwoofer it outputs without effect from the fader control.) Display Setting "SWPRE R" Rear preout. "SWPRE SW" Subwoofer preout. In Standby mode Built-in Amp Setting Built-in amplifier is controlled. Turning OFF this control enhances the preout quality. Display Setting "AMP ON" The built-in amplifier activates. "AMP OFF" The built-in amplifier deactivates. Other than Standby mode B.M.S. (Bass Management System) Adjust the bass boost level of the external amplifier using the main unit. Display Setting "BMS FLT" Bass boost level is flat. "BMS +6" Bass boost level is low (+6dB). "BMS +12" Bass boost level is mid (+12dB). "BMS +18" Bass boost level is high (+18dB). • Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit. • For amplifiers there are the model that can be set from Flat to +18 dB, and the model that can be set from Flat to +12 dB. When an amplifier that can only be set to +12 is connected to the unit, "BMS +18" won’t work correctly even if it’s selected. English | 27 Other than Standby mode B.M.S. Frequency Offset Setting the central frequency boosted by B.M.S. Display Setting "BMSF NML" Boost with the normal central frequency. "BMSF LOW" Drop the normal central frequency 20%. When LX AMP unit connecting AMP Control You can control the LX AMP connected to the unit. 1 Select AMP Control mode Push the Control knob to [FM] or [AM]. Select the "AMP CTRL" display. 2 Enter AMP Control mode Press the Control knob for at least 1 second. 3 Select the AMP Control item for adjustment Push the Contol knob to [FM] or [AM]. • For the details of the AMP Control item, see the Instruction manual attached to the LX AMP. 4 Adjust the AMP Control item...

Herunterladen

Geben Sie zwei Ziffern: