Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Anleitung Kenwood, modell KDC-W5137Y

Hersteller: Kenwood
Dateigröße: 1.16 mb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Dieses Gerät hat auch andere Anweisungen:

Anleitung Zusammenfassung


English | 29 Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Yellow Blue/White Red Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Functions Battery Power Control Ignition (ACC) Earth (Ground) Connection Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1(Default setting) The A-7 pin (red) of the vehicle’s ISO connector is linked with the ignition, and the A4 pin (yellow) is connected to the constant power supply. Ignition cable (Red) A-7 Pin (Red) Unit Vehicle Battery cable (Yellow) A-4 Pin (Yellow) 2The A-7 pin (red) of the vehicle’s ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Ignition cable (Red) A-7 Pin (Red) Unit Vehicle Battery cable A-4 Pin (Yellow) (Yellow) 3The A-4 pin (yellow) of the vehicle’s ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Ignition cable (Red) A-7 Pin (Red) Unit Vehicle A-4 Pin (Yellow) Battery cable (Yellow) . • When the connection is made as in 3 above, the unit’s power will not be linked to the ignition key. For that reason, always make sure to turn off the unit’s power when the ignition is turned off. To link the unit’s power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. 30 | English Installation Installation Metal mounting strap (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. 1 Refer to the section and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button. 3 Tighten the screw (o2 . 5 mm) (Accessory 4) and bracket (Accessory 5 ) in the hole shown on the diagram. Accessory5 Accessory4 4 Tighten the screw (o2 . 5 mm) (Accessory 4) and bracket (Accessory 6) in the hole shown on the diagram. Accessory4Accessory6 ¤ • Never insert the screws in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. English | 31 Installation Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2Removal tool 2 When the upper level is removed, remove the lower two locations. . • The frame can be removed from the bottom side in the same manner. Removing the Unit 1 Refer to the section and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Screw (M4X8) (commercially available) Accessory2 ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. 32 | English Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. ! Cannot switch to Aux source. ^ AUX is not turned on. . (page 25) ! Cannot display the user of System Q. ^

Dieses Handbuch ist für folgende Modelle:
Car-Receiver - KDC-W5137 (1.16 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien