Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
If you want to link the unit’s power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. 28 | English Connecting Wires to Terminals To Steering remote (KDC-W4037/KDC-W3537 : Western European countries sales area only.) .................................................................................................... Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) See next page. To connect these leads, refer to the relevant instruction manuals. Rear left output (White)/ Rear right output (Red)/ Sub Woofer left output (White)/ Sub Woofer right output (Red)/ (KDC-W4037 only) To Kenwood disc changer/ External optional accessory (KDC-W4037/KDC-W3537 only) Antenna Cord (ISO) Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. English | 29 Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Yellow Blue/White Red Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Functions Battery Power Control Ignition (ACC) Earth (Ground) Connection Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1(Default setting) The A-7 pin (red) of the vehicle’s ISO connector is linked with the ignition, and the A4 pin (yellow) is connected to the constant power supply. Ignition cable (Red) A-7 Pin (Red) Unit Vehicle Battery cable (Yellow) A-4 Pin (Yellow) 2The A-7 pin (red) of the vehicle’s ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Ignition cable (Red) A-7 Pin (Red) Unit Vehicle Battery cable A-4 Pin (Yellow) (Yellow) 3The A-4 pin (yellow) of the vehicle’s ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Ignition cable (Red) A-7 Pin (Red) Unit Vehicle A-4 Pin (Yellow) Battery cable (Yellow) . • When the connection is made as in 3 above, the unit’s power will not be linked to the ignition key. For that reason, always make sure to turn off the unit’s power when the ignition is turned off. To link the unit’s power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. 30 | English Installation/Removing the Unit Installation Metal mounting strap (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2Removal tool 2 When the upper lev...
Dieses Handbuch ist für folgende Modelle:Car-Receiver - KDC-W3037 (718.74 kb)
Car-Receiver - KDC-W311 (718.74 kb)
Car-Receiver - KDC-W3537 (718.74 kb)
Car-Receiver - KDC-W4037 (718.74 kb)