Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 1.58 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Car-Receiver - KDC-V7521 (1.6 mb)

Car-Receiver - KDC-V7521 (1.6 mb)

Car-Receiver - KDC-V7521 (3.34 mb)

[4]/ [ . ] buttons Tune up or down band. [#0] — [#9] buttons Press buttons [#1] — [#6] to recall preset stations. [DIRECT] button Enters and cancels the (page 12) mode. [ 38] button Enters and cancels the (page 15) mode. [4]/ [ . ] buttons Doing track forward and [DISC+]/ [DISC–] buttons Doing album forward and backward. [ 38] button Each time the button is pressed the song [DNPP]/ [OK] button Enters and cancels the (page 18) and (page 18), enter the track/disc number. — 29 — English English External view External view ......... Number of ......... Number of 1 4 ......... 1 ......... 1 ......... 2 2 5 ......... 1 3 ......... 1 The use of any accessories except for those provided might damage to the unit. Make sure only to use the accessories shipped the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the left part at the upper side of the faceplate once to make the faceplate control panel appear. 2CAUTION • If your car is not prepared consult your KENWOOD • Only use antenna conversion antenna cord has an ISO plug. • Make sure that all wire connections inserting jacks until they lock completely. • If your vehicle's ignition does not ignition wire is connected to a power voltage such as a battery wire, the power the ignition (i.e., it will not turn on and off ignition). If you want to link the unit's power connect the ignition wire to a power source that on and off with the ignition key. • If the fuse blows, first make sure that the wires have a short circuit, then replace the old fuse with one with rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. — 30 — Connecting Connecting Connector Function Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 Yellow Battery A–5 Blue/White Power Control A–6 Orange/White Dimmer A–7 Red Ignition (ACC) A–8 Black Earth (Ground) Connection Speaker Connector B–1 Purple Rear Right ( + ) B–2 Purple/Black Rear Right ( – ) B–3 Gray Front Right ( + ) B–4 Gray/Black Front Right ( – ) B–5 White Front Left ( + ) B–6 White/Black Front Left ( – ) B–7 Green Rear Left ( + ) B–8 Green/Black Rear Left ( – ) FM/AM antenna input Antenna Cord (ISO) REARFRONT — 31 — TEL MUTE EXT.CONT. P.CONT.OUT ANT.CONT. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Battery wire (Yellow) 6 Ignition wire (Red) 7 Wiring harness (Accessory1) 5 Power control/ Motor antenna control wire (Blue/White) A–7 Pin (Red) A–4 Pin (Yellow) Connector B Fuse(10A) 4 Connector A TEL mute wire (Brown) External amplifier control wire (Pink / Black) manuals. If no connections are made, do not let the cable come out from the tab. 27 Front right output (Red) Front left output (White) Rear right output (Red) Rear left output (White) To KENWOOD disc changer/ DAB control input/ KPA-SD100/KPA-HD100/KPA-SS100 To connect these leads, refer to the relevant instruction To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function. Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. English English 2WARNING Connecting the ISO 31) The pin arrangement of vehicle you drive. Make prevent damage to the unit. The default connection for 1 below. If the ISO connector pins are 2 or 3, make the connection as illustrated. 1 (Default setting) The A-7 pin (red) of connector is linked with the ignition, and is connected to the constant power supply. Unit Vehicle Ignition wire (Red) A–7 Pin (Red) Battery wire (Yellow) A–4 Pin (Yellow) 2 ...

Herunterladen

Geben Sie zwei Ziffern: