Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
(page 7) 15 Installation/connection Caution Part list: A Faceplate.............................................................. (.1) B Escutcheon ......................................................... (.1) C Mounting sleeve ............................................. (.1) D Casing for faceplate ...................................... (.1) E Wiring harness .................................................. (.1) F Removal tool ..................................................... (.2) KDC-U449/ KDC-U3049/ KDC-U349 only: G Flat head screw (for Nissan cars) ........... (.4) H Round head screw (for Toyota cars) .... (.4) Basic procedure 1 Remove the key from the ignition switch, then disconnect the · terminal of the car battery. 2 Make proper input and output wire connections. \ “Wiring connection” (page 17) 3 Install the unit to your car. \ “Installing the unit” (page 18) 4 Reconnect the · terminal of the car battery. 5 Reset the unit. (page 3) Warning The unit can only be installed in a car with a 12 V DC power supply, negative ground. If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Disconnect the battery's negative terminal and make all electrical connections before installing the unit. Insulate unconnected wires with vinyl tape or other similar material. If no connections are made, do not let the wire come out from the tab to prevent short circuit. Be sure to ground this unit to the car's chassis again after installation. If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. Do not use your own screws. Use only the screws provided. Install this unit in the console of your vehicle. Make sure the faceplate will not hit the lid of the console (if any) when closing and opening. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30° or less. If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one that has the same rating. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the · wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. Mounting and wiring this product requires skills and experience. For safety's sake, leave this work to professionals. If you experience problems during installation, consult your Kenwood dealer. ENGLISH KDC-4051UM KDC-U449/ KDC-U3049/ KDC-U349 KDC-U449 KDC-U3049/ KDC-U349/ KDC-4051UM Wiring connection Fuse (10 A)Antenna terminal (JASO) Rear/subwoofer output terminals Front output terminals Rear/subwoofer output terminals Blue/White Brown Blue To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.) Car fuse box Car fuse box Battery Ignition key switchRed (Ignition wire) Yellow (Battery wire) Black (Ground wire) To the metallic body or chassis of the car White ./ White/black ·: To front speaker (left) Gray ./ Gray/black ·: To front speaker (right) Green ./ Green/black ·: To rear speaker (left) Purple ./ Purple/black ·: To rear speaker (right) (Motor antenna control wire) (Power control wire) (Mute control wire) To the power control terminal when using the optional power amplifier. To the antenna control terminal in the vehicle. Light blue/yellow Except for KDC-U3049: To the steering wheel remote control adapter (optional accessory) Blue/White To the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Yellow (A4) Red (Ignition wire)Red (A7) Yellow (Battery wire) ISO connectors (page 18) (Steering remote control wire) (Power control/motor antenna control wire) See also “Connecting the ISO connectors on some VW/Audi or Opel (Vauxhall) automobiles” on page 18. KDC-U449/ KDC-U3049/ KDC-U349 KDC-4051UM KDC-4051UM KDC-U449/ KDC-U3049/ KDC-U349 KDC-U449 KDC-U3049/ KDC-U349/ KDC-4051UM Wiring connection Fuse (10 A)Antenna terminal (JASO) Rear/subwoofer output terminals Front output terminals Rear/subwoofer output terminals Blue/White Brown Blue To the terminal that is grounded when either the telephone rings or during conversation. (To con...
Dieses Handbuch ist für folgende Modelle:Car-Receiver - KDC-U449 (740.45 kb)