Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 576.41 kb Dateiname: Unterrichtssprache:

2 CAUTION Do not set the right side of the faceplate in the faceplate bracket first, when reattaching the faceplate. Doing so may cause the Faceplate lock switch connector on the faceplate bracket to malfunction. 4 Holding the centre part of the faceplate, pull it out. 2 Press the right side of the faceplate until it locks. The faceplate bracket will automatically close. — 12 — "dB" : Recalling the kenwood preset sound setting Press the preset buttons Settings: #1;Flat, #2;Rock, #3;Pops, #6;Scan of #1-5 NOTE If the faceplate bracket's angle was the faceplate was mounted, check that attached to the faceplate bracket by holding pulling it gently towards you. NOTE • This mode is available only when is on. (page 36) • You can call the following settings centre frequency, bass level, bass quality extension, treble centre frequency, and Their setting values are different depending the mobile preset plan mode. Audio Control Setting Adjust various parameters of sound quality. 1 Press the AUD button to enter the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change. Please refer to the following for the contents of the adjustment modes. NOTE Source tone memory Each source (CD, FM, AM, and disc changer) has its own memory in which to store the bass, treble and N-F level settings. The settings made for a particular source are then recalled automatically whenever you use that source (e.g., FM mode uses the tone settings made for FM, AM for AM, etc.). 3 Adjust each mode Press the 4/ . button. Look at the table to adjust the mode being displayed. 4 Press the AUD button to end the control mode. “Bass Frq” : Adjust the centre frequency of the bass. Setting values: 60 / 70 / 80 / 100 (Only when the bass quality factor is set to 1.00, 1.25 or 1.50) / 150 (Only when the bass quality factor is set to 2.00) Hz NOTE This mode is available only when the Sound coordinate system is on. (page 36) “Bass” : Adjust the bass level. Setting values: - 8 – + 8 “Bass Q” : Adjust the Bass quality factor. Setting values: 1.00 / 1.25 / 1.50 / 2.00 NOTE This mode is available only when the Sound coordinate system is on. (page 36) — 13 — General features English “Bass EXT” : Switch the Bass Extend mode on/off. Setting values: ON / OFF (When the bass extend frequency response is extended NOTE This mode is available only when on. (page 36) “Tre Frq” : Adjust the centre frequency of the treble. Setting values: 10.0 / 12.5 / 15.0 / 17.5 kHz NOTE This mode is available only when the Sound coordinate on. (page 36). “Tre” : Adjust the treble level. Setting values: - 8 – + 8 “Balance” : Adjust the balance level. Setting values: Left 15 – Right 15 “NFpre Level” : Adjust the Non-fading output level. Setting values: - 15 – + 15 NOTE • This mode is available only is set to on. (KDC-8080R only) • Not available during the Dual zone “HPF Front” : Adjust the frequency of the High-pass filter for front output. Setting values: Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz / 150Hz / 180Hz / 220Hz NOTE You can separately set the high-pass filter for front and rear output, including preouts. The high-pass filter works except during non-fading preout when switching to non-fading (KDC8080R only). The factory default settings for front output and rear output are "through" . “HPF Rear” : Adjust the frequency of the High-pass filter for rear output. Setting values: Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz / 150Hz / 180Hz / 220Hz NOTE “Fader” : Adjust the fader level. Setting values: Front 15 – Rear 15 You can separately set the high-pass filter for front and rear output, including preouts. The high-pass filter works except during non-fading preout when switching to non-fading (KDC8080R only). The factory default settings for front output and rear output are "through" . — 14 — • The settings you “LPF NFpre” : Adjust the frequency of the Low-pass filter for level, bass quality frequency, and treble Non-Fading output. Setting values: 50 Hz NOTE • This mode is available only when is set to on. (KDC-8080R only) Recalling your sound settings: • Not available during the Dual zone Press a preset button (#1-6) except frequency, bass level, bass quality factor, treble center frequency, and treble level NOTE “NFpre Phase” : Adjust the phase for Non-Fading output. This mode is available only when Sound coordinate Setting values: Normal (0°) / Reverse (180°) (page 36) NOTE • This mode is available only when the non-fading output is set to on. (KDC-8080R only) • Not available during the Dual zone system is on. “VOL OFFSET” : Set the sound level of the each source selected by adjusting the level difference between the basic sound level and the required level. Setting values: - 8 – 0 Storing your sound settings: Hold down a preset button (#1-6) for two seconds or more except during the bass center frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level adjust mode...

Herunterladen

Geben Sie zwei Ziffern: