Login:
Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Anleitung Kenwood, modell KDC-MP439

Hersteller: Kenwood
Dateigröße: 587.92 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Dieses Gerät hat auch andere Anweisungen:

Anleitung Zusammenfassung


English | 15 Connecting Wires to Terminals Front preput(KDC-MP439 only) FM/AM antenna input Fuse (10A) To Kenwood disc changer/ External optional accessory (KDC-MP439 only) Rear preput/ Subwoofer preput FRONT Ground wire (Black) - (To car chassis) Wiring harness (Accessory1) Ignition wire (Red) Battery wire (Yellow) ACC Car fuse box If no connections are made, do not let the wire come out from the tab. To front left speaker To front right speaker To rear left speaker To rear right speaker White/Black White Gray/Black Gray Green/Black Green Purple/Black Purple Ignition key switch Car fuse box (Main fuse) Not Used (Blue) TEL mute wire (Brown) Connect to the terminal that is grounded when either the telephone rings or during conversation. .To connect the Kenwood navigation system, consult your navigation manual. Power control/Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. .Do not let the wire come out from the tab. –+ P.CONT MUTE ANT. CONT Battery 16 | KDC-MP439/KDC-MP3039/KDC-MP339/KDC-MP239/KDC-139 Installation non-Japanese cars Metal mounting strap (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Japanese cars 1 Refer to the section and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2Removal tool 2 When the upper level is removed, remove the lower two locations. . • The frame can be removed from the bottom side in the same manner. Removing the Unit 1 Refer to the section and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Screw (M4X8) (commercially available) Accessory2 8 mm MAX. o5mm o5mm 8mm MAX. Accessory3...for Nissan car Accessory4...for Toyota car 34 T N T N T/N T: Toyota cars N: Nissan cars ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. English | 17 Troubleshooting Guide Some functions of this unit may be disabled by The messages shown below display your some settings made on this unit. systems condition. ! TOC ERR/E-04: • No disc has been loaded in the disc Cannot display the user of System Q. magazine. ^

recorded that the unit can play. (page 10) • (page 4) is not set to On. E-77: The unit is malfunctioning for some reason. . Press the reset button on the unit. If the “E! 77” code does not disappear, consult your • Cannot register a security code. nearest service center. • Cannot set up Display. ^ (page 12) is not E-99: Something is wrong with the disc magazine. turned off. Or the unit is malfunctioning for some reason. ! . Check the disc magazine. And then press Cannot play audio files.the reset button on the unit. If the “E-99” ^ “CD READ” is set to “2”. . (page 10) code does not disappear, consult your nearest service center. READING: The unit is reading the data on the disc. What might seem to be a malfunction in your unit may just be the result of slight misoperation or IN (Blink): The CD player section is not operating properly. miswiring. Before calling service, first check the . Reinsert the CD. If the CD cannot be following table for possible problems. ejected or the display continues to flash even when the CD has been properly Tuner source ? reinserted, please switch off the power Radio reception is poor. and consult your nearest service center. . The car antenna is not extended. PROTECT/DCER: The speaker wire has a short-circuit or . Pull the antenna out all the way. touches the chassis of the vehicle, and then the protection function is activated. Disc source ? . Wire or insulate the speaker cable properly and press the reset button. If The spe...

Dieses Handbuch ist für folgende Modelle:
Car-Receiver - KDC-139 (587.92 kb)
Car-Receiver - KDC-MP239 (587.92 kb)
Car-Receiver - KDC-MP3039 (587.92 kb)
Car-Receiver - KDC-MP339 (587.92 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien