Anleitung Kenwood, modell KDC-D301
Hersteller: Kenwood Dateigröße: 268.3 kb Dateiname:
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
When the centre unit is compatible with the "N"-operation, set the O-N switch to "N". When it is not compatible with the "N" operation, set the O-N switch to "O" because the operation is not available. The initial setting of the switch is "N". 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Set the O-N switch of this unit to suit the centre unit. 3. Connect the speaker input cable to the front speaker cable of the wiring hernees of the centre unit. 4. Connect the control cable to the control connector. 5. Install the unit in your car. 6. Reconnect the - battery. 7. Press the reset button on the centre unit. N O N O – + – + FRONT • L FRONT • R R L KDC-D301 Control input White/Black White Gray/Black Gray White/BlackWhite Gray/BlackGray Speaker input cable ( Accessory2) 2CAUTION • Do not connect the changer control cable while the centre unit is turned ON. • Be sure to press the reset button after installation. • Whether the centre unit in use is compatible with the "N" operation or not can be identified by referring to its instruction manual (description of the disc control mode, etc.). • If you use the changer switching unit, see the instruction manual for the KCA-S210A included in the unit. switch on the KCA-S200 to "O." • Do not let unconnected wires or terminals car or anything else conducting electricity. circuit, do not remove the caps on the wires or the terminals. • After the unit is installed, check whether blinkers, wipers, etc. on the car • Mount the unit so that the mounting or less. 2CAUTION If the speaker input the spectrum — 10 — Installation Screw (M4X8) (commercially available) (Accessory3)* Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Installation Screw (M4X8) (commercially available) (Accessory3)* Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Metal mounting strap (commercially available) (Accessory4)* (North & South America sales ¦ Installation *…North & South America sales area only. ¦ Screwing the Faceplate on the Unit area only.) If you want to fasten the faceplate to the main unit so that it does not fall off, insert the provided screw (o2.6 . 12 mm) in the holes as follows. Firewall or metal support 1 Insert one of the provided screws into hole. so that the screw is perpendicular to the bottom panel of the unit. 2 Similarly, insert another provided screw into hole ™ . Ensure that the faceplate is fixed firmly before operating this unit. Bottom panel Hole. Hole ™ Accessory7 2CAUTION Never insert the taptite screws (o2.6 . 12 mm) in any other screwSelf-tapping attach it in place. holes than the one specified. If you insert it in another hole, it will screw contact and may cause damage to the mechanical parts inside the(commercially unit. available) (North & South America sales area ¦ Installing in Japanese-Made Cars only.) 1 Refer to the section “Removing the hard rubber frame and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each vehicle mounting blacket and secure the unit with screws. 8 mm MAX. 5mm 5mm 8 mm MAX. T N N T T/N 5 6 T: Toyota cars Accessory5...for Nissan car N: Nissan cars Accessory6 ...for Toyota car 2CAUTION • During installation, do provided. The use the main unit. • Damage may excessive — 11 — Installation Installation Removing the hard rubber frame ¦ Removing the Unit English 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Catch Lock Accessory1 Removal tool 2 When the lower level is removed, remove the upper two locations. 1 Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. 2 Remove the Hex-head screw with integral washer (M4.8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) (Accessory3 : North & South America sales area only. ) Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch 2CAUTION Catch facing up NOTE The frame can be removed from manner. — 12 — Troubleshooting Guide Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No cable has been connected to the disc changer input Connect the control cable to the disc changer input terminal be selected. terminal on the unit. on the centre unit. No CD has been inserted. For centre units brought on to the market from 1999 onwards, it is not possible to switch to the CD mode unless a CD has already been inserted. No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all the way to one Reset the fader or balance settings. side. 5 minutes have elapsed since the panel d...