Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
F AuInstallation using the trim mount plateH CD AUTO CHANGER CONTROLLER DISC TRACK REP RDM 34. 1A RWR 'M.RDM D.REP D.SCN DISC TRACK 8/Display unit H Pass the cable from the Display unit through the hole on the trim mount plate and push fit the Display unit into the trim mount plate until it locks. 2CAUTION • Be sure not to place the unit on such place as where it is exposed to direct sunlight and temperature eventually rises. It results in the deformation of the case. • Depending on the installing location, the display unit may not be able to receive the signals from the controller unit. Install them after confirming that the signals can be received. • Install the unit in such a way that it does not disturb driving. 26 Troubleshooting guide Often, what appears to be a malfunction is due to user error. Before calling for service please consult the following table. Symptom Cause Remedy The power is not turned on. The wiring harness fuse blows. Check cables for shorts, then replace the fuse with one of with the same rating (shown on the case). No sound or sound is low. The volume level is minimum. Raise the volume level. The fader or balance is set to one side. Adjust the fader and balance. The input/output cable or wiring harness is connected incorrectly. Connect the input/output cable or wiring harness correctly. See "Connections" (Page 22). The unit does not work properly when a button is pressed. The microcomputer malfunctions. Press the Reset button of the display unit. Sound quality is poor. (Sound distortion) The volume level is too high. Use the appropriate volume level. CD play does not start. CD auto-changer input is not connected to the unit. Connect the CD auto-changer input to the unit. Power button is not turned ON. Turn the power button ON. The specified disc is not played; a different disc is played instead. The disc is loaded upside down. The specified disc is very dirty. Eject the disc magazine and insert the disc correctly. Check and, if possible, clean the disc. See "Cleaning your discs" (Page 6). Two discs are inserted in a slot. Eject the disc magazine and insert the discs correctly. The number of the slot into which the disc is inserted is different from the number of the specified disc. Eject the disc magazine and check the number of the specified disc. The disc is severely damaged. Use another disc. Sound skips due to vibration. Something is touching the CD auto- changer. Keep it away from the CD auto-changer. The disc is dirty or damaged. If sound skips at the same part, the disc is faulty. Check and, if possible, clean the disc. See "Cleaning your discs" (Page 6). The unit is mounted at a slant. Mount the unit so that is level. Changer unit is mounted in an unstable place. Mount the unit in a stable place. The angle adjustment switches are set improperly. Set the angle adjustment switches to the correct positions. Nothing appears on the display. The control output of the display unit is not connected properly. Connect the control output properly. Sound distortion. A disc with a high recording level is used. Change the modulation level / dynamic control setting.(Page 20) Troubleshooting guide 27 Troubleshooting guide Troubleshooting guide Symptom Cause Remedy Sound quality is poor. The recording of the disc is poor. Try playing another disc. If the sound is good, the fault was with the original disc. The disc is dirty or damaged. Check and, if possible, clean the disc. See "Cleaning your discs. (Page 6)" No sound is heard even though the information concerning the CD auto- changer is displayed. The microcomputer does not function correctly. Volume is set to minimum level. Press the Reset button of the display unit. Raise the volume level. The system is not connected properly. Connect the system properly. See "Connections" .(Page 22) The specified track is not played. The player is set to RANDOM PLAY/MAGAZINE RANDOM PLAY. Turn off RANDOM PLAY/MAGAZINE RANDOM PLAY. The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. 01 E: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. >Load the disc magazine properly. 02 E: No disc has been loaded in the disc magazine.. >Load a disc into the disc magazine. 04 E: No disc has been loaded in the disc magazine. >Load a disc into the disc magazine The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. >Clean the CD and load it correctly. 77 E: The unit is malfunctioning for some reason. >Press the reset button on the unit. If the "E- 77"code does not disappear, consult your nearest service center. 99 E: Something is wrong with the disc magazine. Or the unit is malfunctioning for some >reason.Check the disc magazine. And then, press the reset button on the unit. If the "E- 99" code does not disappear, consult your nearest service center. 0d E: The protective circuit in the unit activates when the temperature inside the automatic d...