Light Blue/Yellow (Steering remote control) To Kenwood disc changer/ External optional accessory .To connect these leads, refer to the relevant instruction manuals. To connect the Kenwood navigation system, consult your navigation manual. USB connector (0.8 m (2.7 ft)) To USB device .Do not remove the cap when you do not use the USB cable. The connector will cause the unit to malfunction if it gets in touch with any metallic part of the vehicle. Wiring harness (Accessory1) AUX input (Stereo) Use the mini-plug which is stereo type and does not have any resistance. (3.5mm(1/8”)o) Antenna Cord 68 | KDC-X995/ KDC-BT948HD Installation/Removing the Unit non-Japanese cars Removing the hard rubber frame Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Japanese cars 1 Refer to the section and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. 8 mm MAX. o5mm o5mm 8mm MAX. T N T N T/N T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4...for Toyota car 34 ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2Removal tool 2 When the upper level is removed, remove the lower two locations. . • The frame can be removed from the bottom side in the same manner. Removing the Unit 1 Refer to the section and then remove the hard rubber frame. 2 Detach the faceplate. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Accessory2 ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. English | 69 Installation/Removing the Unit Installation the Microphone Unit 1 Check the installation position of the microphone (accessory 5). 2 Remove oil and other dirt from the installation surface. 3 Install the microphone. 4 Wire the cable up to the unit with it secured at several positions using tape or the like. Fix a cable with a commercial Accessory 5 item of tape. Peel the release coated paper of double-face adhesive tape to fix on the place shown above. Adjust the direction of the microphone to the driver. . • Install the microphone as far as possible from the cellphone. 70 | KDC-X995/ KDC-BT948HD Troubleshooting Guide Some functions of this unit may be disabled by What might seem to be a malfunction in your unit some settings made on this unit. may just be the result of slight misoperation or miswiring. Before calling service, first check the • Cannot set up the subwoofer. following table for possible problems. • No output from the subwoofer. General • Cannot set up the subwoofer position of Manual ! position setting. ? The operation check sound (beep sound) does not • The Dual zone function is enabled. . (page 42) . The preout jack is being used. • In the speaker select option, None is selected for . The Touch Sensor Tone cannot be output from the subwoofer. . (page 44) the preout jack. ? ! The illumination flashes when the knob or button • Cannot set up the equalizer. is operated. • Cannot set up the Bass Boost. . This is the key illumination effect. • Cannot set up the Highway sound. . You set this effect in “ILLUMI Effect” of (page 30). • Cannot set up the Position control. • The Dual zone function is enabled. . (page 42) conjunction with the sound volume is small. • The DSP function is disabled. . “DSP Set” of
