Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 925.21 kb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Car-Receiver - KDC-4027V (1.02 mb)

Car-Receiver - KDC-4027V (1.36 mb)

Power OFF Timer Setting the timer to turn this unit's power OFF automatically when Standby mode continues. Using this setting can save the vehicle's battery power. Display Setting "OFF – – –" Power OFF Timer function is OFF. "OFF 20M" Turns the power OFF after 20 minutes. (Original setting) "OFF 40M" Turns the power OFF after 40 minutes. "OFF 60M" Turns the power OFF after 60 minutes. — 21 — English English External view Number of items .......................................... 1 1 .......................................... 2 2 .......................................... 1 3 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the disconnect the - terminal of the battery. 2. Make the proper input and output wire connections 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness speaker connector in your vehicle. 5. Take Connector A on the wiring external power connector 6. Connect the wiring harness 7. Install the unit in your 8. Reconnect the - terminal of the battery. 9. Press the reset 2CAUTION • If your car is not prepared for this special connection-system, consult your Kenwood dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug. • Make sure that all wire connections are securely made by inserting jacks until they lock completely. • If your vehicle's ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the unit's power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the faceplate does not hit the lid when closing • Mount the unit so that the mounting angle or less. — 22 — Connecting Wires to Terminals 14 Connecting Wires to Terminals 14 To connect the Disc changer, consult your Antenna Conversion Adaptor Disc changer manual. (ISO–JASO) (Accessory3) To Steering remote (Blue/Yellow) Antenna Cord (ISO) (Optional Accessory) REAR L R REMO.CONT Connector Function Guide Pin Numbers for ISO Connectors Wire Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) — 23 — 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 P.CONT ANT.CONT TEL MUTE Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) See page 24 TEL mute wire (Brown) Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. English English 2WARNING Connecting the ISO Connector (see p.23) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (y...

Herunterladen

Geben Sie zwei Ziffern: