Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Kenwood Dateigröße: 539.88 kb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Car-Receiver - KDC-4021V (698.89 kb)

The data is automatically stored, allowing you to switch quickly to another RDS stations, broadcasting the same programme, that has better reception. These include stations stored in the station preset memory that you often listen to. Enhanced Other Network Stations that offer also transmit information about other RDS stations that have traffic information. When you are tuned to a station that is not transmitting traffic information, but another RDS station starts transmitting a traffic bulletin, the tuner automatically switches to the other station for the duration of the bulletin. Alarm When an emergency transmission (announcing disasters, etc.) is sent, all current functions are interrupted to allow the warning to be received. Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it. When using a new CD If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc. Burrs Burrs CD accessories Don’t use disc type accessories. CD cleaning Clean from the center of the disc and move outward. Removing CDs When removing CDs from this unit pull them out horizontally. CDs that can’t be used • CDs that aren’t round can’t be used. • CDs with coloring on the recording surface or that are dirty can’t be used. • Don’t use CDs without disc mark . •A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.) CD storage • Don’t place them in direct sunlight (On the seat or dashboard etc.) and where the temperature is high. • Store CDs in their cases. — 5— English English Power Release button AM FM .4ud SRC ATT/ CLK Q/ LOUD AUD LOUD indicator ATT indicator SYSTEM Q indicator Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUNER" CD "CD" External disc "DISC" (Function of the KDC-4021/KDC-4021V) Standby (Illumination only mode) "ALL OFF" This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicles battery. The time until full power OFF can be set in (page 21). Volume Increasing Volume Press the [u] button. Decreasing Volume Press the [d] button. — 6— Attenuator Attenuator Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. Easy "EASY" Scan of Flat — Easy "SCAN" • Each setting value is changed with the (page 8). First, select the speaker type with the Speaker setting. • When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. Loudness Compensating for low and high tones during low volume. Press the [LOUD] button for at least 1 second. Each time the button is pressed for at least 1 second the Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. Audio Control System Q You can recall the best sound setting preset for different types of the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the sound setting switches. Sound setting Display 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below. 4 Adjust the Audio item Press the [4] or [.] button. Adjustment Item Display Range Bass level "BAS" –8 — +8 Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BAL" Left 15 — Right 15 Fader "FAD" Rear 15 — Front 15 Flat "FLAT" 5 Exit Audio Control mode Rock "ROCK" Press the [AUD] button. Top 40 "TOP40" Pops "POPS" Jazz "JAZZ" — 7 — General features General features Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "ALL OFF" display. 2 Enter Speaker Setting mode Press the [Q] button. 3 Select the Speaker type Press the [4] or [.] button. Each time the button is pressed the setting switches as shown below. Speaker type Display OFF "SP OFF" For the OEM speaker "SP OEM" For 6 & 6x9 in. speaker "SP 6/6x9" For 5 & 4 in. speaker "SP 5/4" 4 Exit Speaker Setting mode Press the [Q] button. Switching Display Switching the information displayed. Press the [CLK] button. Each time the button is pressed the display switches as shown below. In Tuner source Information Display Program Service name or Frequency Clock In CD & External disc source Information Display Track Time Disc name* "D-NAME" Disc...

Herunterladen

Geben Sie zwei Ziffern: