Stimmen - 0, Durchschnittliche Bewertung: 5 ( )

Hersteller: Kenwood Dateigröße: 812.48 kb Dateiname: Unterrichtssprache:

"NF ON" is displayed when the non- The . indicator lights whilst the clock is displayed. Function of the KRC-PS978R/KRC-878R Switching Spectrum Analyzer Display You can change the display in each mode. Changing the Display: Each time you press the CLK button, the display switches as follows: Character Track time (Only during disc play) Track number (Only during disc play) Clock NOTE The . indicator lights whilst the clock is displayed. — 9— General features TEL Mute NOTE English Shut down the audio incoming call is received. NOTE The function will not work if phone. When the telephone rings: When a call is received, "CALL" is displayed functions are temporarily interrupted. Restoring Original Unit Source During Phone Call: Press the SRC button. "CALL" disappears from the display, and the volume original source is restored gradually. Turning TEL Mute Function Off After Phone Call: Hang the phone up. "CALL" disappears from the display. The original source (i.e., the one used before the phone call) returned to automatically, and the volume restored gradually. If the faceplate's angle mounting the faceplate difficult to mount the faceplate securely attached and could Set the angle adjustment switch faceplate. 3 Slide the faceplate lock switch to which you have set in the "Time setting faceplate" in the menu. Faceplate lock switch 4 Holding the centre part of the faceplate, pull it out. The faceplate bracket will automatically close. Removing the Faceplate The faceplate can be detached from the unit, helping to deter theft. Removing the faceplate: 1 Choose the way from among the following and open the faceplate. Turn the ignition off, hold down the SRC button for one second or more, or press the left part at the upper side of the faceplate (as illustrated on p.8) for as many times as you have preset in the "Manual Open Button Setting" (OPEN SW #) in the menu when the control panel has been hidden. 2 Set the faceplate's angle adjustment switch to "0" to set the faceplate angle to the vertical. For details, refer to "Faceplate Angle Adjustment" (page 8) . 2 CAUTION • When removing the faceplate, pull it out only when it is fully open. The detachment of the faceplate whilst it is moving might result in damage to the unit. • Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. • Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. • Do not touch two metal parts on both sides of the faceplate bracket. Touching those parts may injure you. NOTE • Sliding the faceplate lock switch cause the unit’s power to turn off. If you want to operate the unit again, remove the faceplate from the faceplate bracket completely and then reattach it. — 10 — • The faceplate is damaged by shocks in its special storage • Do not expose the faceplate sunlight or excessive heat too much dust or the possibility Reattaching the Faceplate: 1 Hold the faceplate so that the control toward you and set the left side of faceplate bracket. 2 CAUTION Do not set the right side of the faceplate in first, when reattaching the faceplate. Doing so connector on the faceplate bracket to malfunction. 2 Press the right side of the faceplate until it locks. NOTE Please refer to adjustment modes. NOTE Source tone memory Each source (tape, CD, memory in which to store The settings made for a particular automatically whenever you use the tone settings made for FM, AM 3 Adjust each mode Press the 4/ . button. Look at the table to adjust the mode being 4 Press the AUD button to end the control mode. "Kex"/"ec4"/"dB" : Recalling the kenwood preset sound setting Press the preset buttons (#1-6). Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy, #6;Scan of #1-5 If the faceplate bracket's angle was not set to the vertical when the faceplate was mounted, check that the faceplate is securely attached to the faceplate bracket by holding its right side and pulling it gently towards you. Audio Control Setting Adjust various parameters of sound quality. 1 Press the AUD button to enter the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change. NOTE • This mode is available only when the Sound coordinate system is on. (page33) • You can call the following settings with this function; bass centre frequency, bass level, bass quality factor, bass extension, treble centre frequency, and treble level setting. Their setting values are different depending on the setting of the mobile preset plan mode. — 11 — General features English "Bas F/Bass F" : Adjust the centre frequency of the bass. Setting values: 60 / factor is set to 1.00, 1.25 quality factor is set to 2.00) NOTE This mode is available only when on. (page33) "Bas/Bass " : Adjust the bass level. Setting values: - 8 – + 8 "Bas Q/Bass Q" : Adjust the Bass quality factor. Se...

Herunterladen

Geben Sie zwei Ziffern: