Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Kenwood Dateigröße: 828.46 kb Dateiname: Unterrichtssprache:

CONT — 19 — Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) Ignition key switch ACC 15 Car fuse box Battery Power control/ Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. If no connections are made, do not let the wire come out from the tab. Car’s wiring harness Car fuse box (Main fuse) To front left speaker To front right speaker To rear left speaker To rear right speaker English English ¦ Connector Function 101 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8Connector A Connector B Pin Numbers Plug Functions for ISO Connectors setting* A–4 1 Battery 2 Ignition (ACC) A–5 Power Control A–7 1 Ignition (ACC) 2 Battery A–8 Earth (Ground) Connection B–1 Rear Right (+) B–2 Rear Right (–) B–3 Front Right (+) B–4 Front Right (–) B–5 Front Left (+) B–6 Front Left (–) B–7 Rear Left (+) B–8 Rear Left (–) *Plug setting: See right side. — 20 — 20— 20 — —— ¦ Plug Setting 2WARNING Connecting the ISO The pin arrangement for of vehicle you drive. Make to prevent damage to the unit. 1 The A-7 pin of the vehicle's ISO ignition, and the A-4 pin is connected supply. (Default setting) 10 2 The A-7 pin of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin is linked to the ignition. 10 • If both the A-7 pin and A-4 pin are connected to the vehicle constant power supply, use Plug setting 2. • If the A-7 pin is connected to the vehicle constant power supply, and the A-4 pin isn't connected to anything, wire the unit using the Wiring harness (Accessory 1). Installation Installation Power Control Connections The output of the Power the power on/off switching This terminal can be connected CON (REMOTE) terminal of the amplifier, or used as the power supply antenna adapter for Volkswagen cars. (MAX. 300 mA) Power Control terminal (Flat terminal) Power Amplifier Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Power control wire Special antenna adapter (For Volkswagen car) (Commercially available) Metal mounting strap (commercially available) Self-tapping Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installation Firewall or metal support screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). — 21 — 21— 21 — —— Installation Installation ¦ Removing the 1 Engage the catch pins locks on the lower level. Lower the frame and pull 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. Catch Lock Accessory2 Removal tool ¦ Removing the 1 Refer to the section then remove the hard 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools as shown. Accessory2 Removal tool Screw (M4X8) (commercially available) 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 22 — 22— 22 — —— Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? If you have selected Standby mode, the power will automatically. . The Power OFF Timer function has been activated. . If you do not want the power to go OFF automatically, cancel the Power OFF Timer function. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? The TEL mute function . The TEL mute wire . Connect the wire correctly, referring to the section . ? The TEL mute function turns not connected. . The TEL mute wire is touching a metal . Pull the TEL mute wire away f...

Herunterladen

Geben Sie zwei Ziffern: