Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 829.02 kb Dateiname: Unterrichtssprache:

Display and setting the frequency: "REAR HPF" : THROUGH / 30Hz / 60Hz / 90Hz / 120Hz / 150Hz / 180Hz / 250Hz Display and setting the slope: "REAR Slope" : 12dB / 18dB / 24dB NOTE • You cannot operate when the “ Sub Woofer“ is set to “ OFF“ (page.29). • You cannot operate when the “ Multi CH“ is set to “ 3/0“ or “ 2/0“ (page 29) . • The slope setting can’t be adjusted when the frequency setting is THROUGH. — 25 — Audio effect control features Audio effect control features English 5.Delay Time for the Rear Right Speaker Adjust the delay time for rear right output. Display and setting: "R-R DTA" : 0.0m / 0.1m / 0.3m / 0.4m / 0.6m / 0.7m / 0.9m / 1.0m / 1.2m / 1.3m / 1.5m / 1.6m / 1.8m / 1.9m / 2.1m / 2.2m / 2.4m / 2.5m / 2.7m / 2.8m / 3.0m / 3.3m / 3.6m / 3.9m / 4.2m / 4.5m / 4.8m / 5.1m / 5.4m / 5.7m / 6.0m NOTE You cannot operate when the “ Multi CH“ is set to “ 3/0“ or “ 2/0“ ( page 29 ) . 6.Delay Time for the Rear Left Speaker Adjust the delay time for rear left output. Display and setting: "R-L DTA" : 0.0m / 0.1m / 0.3m / 0.4m / 0.6m / 0.7m / 0.9m / 1.0m / 1.2m / 1.3m / 1.5m / 1.6m / 1.8m / 1.9m / 2.1m / 2.2m / 2.4m / 2.5m / 2.7m / 2.8m / 3.0m / 3.3m / 3.6m / 3.9m / 4.2m / 4.5m / 4.8m / 5.1m / 5.4m / 5.7m / 6.0m NOTE You cannot operate when the “ Multi CH“ is set to “ 3/0“ or “ 2/0“ ( page 29 ) . Display and setting the slope: "SW Slope" : 12dB / 18dB / 24dB NOTE You cannot operate when the “ Sub Woofer“ is set to "OFF" ( page 29 ). 8.Delay Time for the Sub Woofer Adjust the delay time for sub woofer output. Display and setting: "SW DTA" : 0.0m / 0.1m / 0.3m / 0.4m / 0.6m / 0.7m / 0.9m / 1.0m / 1.2m / 1.3m / 1.5m / 1.6m / 1.8m / 1.9m / 2.1m / 2.2m / 2.4m / 2.5m / 2.7m / 2.8m / 3.0m / 3.3m / 3.6m / 3.9m / 4.2m / 4.5m / 4.8m / 5.1m / 5.4m / 5.7m / 6.0m NOTE You cannot operate when the “ Sub Woofer“ is set to “ OFF“ ( page.29 ). 9.High-pass Filter for Centre Output Adjust the frequency of the High-pass filter for Centre output. Display and setting the frequency: "CNTR HPF" : THROUGH / 30Hz / 60Hz / 90Hz / 120Hz / 150Hz / 180Hz / 250Hz Display and setting the slope: "CNTR Slope" : 12dB / 18dB / 24dB NOTE 7.Low-pass Filter for Sub Woofer Output Adjust the frequency of the Low-pass filter for Sub Woofer output. Display and setting the frequency: "SW LPF" : 30Hz / 60Hz / 90Hz / 120Hz / 150Hz / 180Hz / 250Hz • You cannot operate when the “ Sub Woofer“ is set to “ OFF“ (page 29). • You cannot operate when the “ PCM Center“ is set to "OFF" (page 29) . • You cannot operate when the “ Multi CH“ is set to “ 2/2“ or “ 2/0“ (page 29) . — 26 — 10.Delay Time for the Centre Speaker 10.Delay Time for the Centre Speaker Display and setting: "CNTR DTA" : 0.0m / 0.1m / 0.3m / 0.4m / 0.6m / 0.7m / 0.9m / 1.0m / 1.2m / 1.3m / 1.5m NOTE • You cannot operate when the “ PCM Center“ is set to "OFF" (page 29) . • You cannot operate when the “ Multi CH“ is set to “ 2/2“ or “ 2/0“ (page 29) . 11.Phase for Sub Woofer Output When the Noise sequencer is turned ON, only item 10 can be Adjust the phase for Sub Woofer output. adjusted. Display and setting: "SW Phase" : Normal (0° ) / Reverse (180° ) Surround Processor Control Adjust various parameters of sound quality. 1 Hold down the Q button to enter the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change. Please refer to the following for the contents of the adjustment modes.(Items 1-10 can be adjusted in this Adjustment mode. ) 3 Adjust each mode Press the 4/ . button. Please refer to the following for the adjusting values. 4 Press the Q button to end the control mode. NOTE NOTE You cannot operate when the “ Sub Woofer“ is set to “ OFF“ (page.29). 1.Recalling the Kenwood Preset Sound You can recall the best audio setting preset for different types of the music. Display and Setting: “ FLAT“ / “ POPS“ / “ ROCK“ / “ DANCE“ / “ VOCAL“ / “ CLASSIC“ . 12.Storing Your Setting of the Crossover network/Delay time Press the #1 - #6 button for at least two seconds. Recalling your settings of the Crossover network/Delay time Press the #1 - #6 button for the desired crossover network and delay time setting. NOTE • “ User” displays each item when it’s adjusted. • Not available during the Dual zone system is on. — 27 — English English 2.Parametric Equalizer Each time you press the FM or AM button, will be switched as follows: "BAND- 1 f" / "BAND- 1 Gain" / "BAND- 1 Q" / "BAND- 2 f" / "BAND- 2 Gain" / "BAND- 2 Q" / "BAND- 3 f" / "BAND- 3 Gain" / "BAND- 3 Q" / "BAND- 4 f" / "BAND- 4 Gain" / "BAND- 4 Q" Adjusting the Centre Frequency: Display and Setting: "BAND- 1 f" : 60Hz/ 80Hz/ 100Hz/ 120Hz/ 160Hz/ 200Hz/ 250Hz "BAND- 2 f" : 315Hz/ 400Hz/ 500Hz/ 630Hz/...

Herunterladen

Geben Sie zwei Ziffern: