Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
3. Slide the unit and frame into the dash opening. 4. Install the dash panel or adapter plate. 5. Install the trim ring to the unit. 6. Install the control panel to the unit. Connecting 9 Connection Connecting to a car Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. To Audio out To Audio in 2 Connecting abcdefghabcdefghabcdefghAAAAAAAAA a Gray: Front Right + A b Gray/ Black Stripe: Front Right - A cViolet: Rear Right + A dViolet/ Black Stripe: Rear Right - A eWhite: Front Left + A fWhite/ Black Stripe: Front Left - A g Green: Rear Left + A h Green/ Black Stripe: Rear Left - Power Antenna Control Relay (Optional) (Optional) Amplifi er (Optional) Rear Left (Sub-woofer Left) Front Left Rear Right (Sub-woofer Right) Front Right Amplifi er (Optional) B f Power Antenna (Blue) B g Dimmer (Pink) B cTo Ignition (Red) B h Ground (-) (Black) B dTo Battery (+) (Yellow) B e Remote On (Blue/ White) (Optional) B b Phone Mute (Orange) (Optional) B a Not connected Dimmer Switch Ignition Switch 10 Operating 3 Operating Operation Basic operations 1. Turn the unit on by pressing any key on the unit. 2. Select a source by pressing SRC. 3. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W/S on the remote control. Note , If a source is not connected to the unit, the source is not recognized. Turning off the sound temporarily 1. Press MUTE to mute your unit. Or press MUTE on the remote control. 2. To cancel it, press MUTE again. Using EQ (Equalizer) EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press EQ/ • XDSS+ on the unit repeatedly. The indicator lights up in the following order. POP / CLASSIC / ROCK / JAZZ / VOCAL / SALSA / SAMBA / REGGAE / RUSSY / USER 1 / USER 2 / Off (not displayed) Note , • When XDSS+ is set to "Off", you can adjust the EQ settings. • You can adjust sound level to your preference. Once you select a USER 1/2 mode and press ` on the unit, then adjust the sound level (BASS (bass), MID (middle), TRB (treble), BAL (left/right speaker), FAD (front/rear speaker), S--W (Sub-woofer: optional)), it will be automatically stored for the currently selected USER 1/2 mode. Refer to the "For [SOUND] setting" for USER 1/2 mode on the page 11. Using XDSS+ (Extreme Dynamic Sound System) It improves the treble and bass sound. 1. Press and hold EQ/ • XDSS+ on the unit. 2. To cancel it, press and hold it again. Checking the clock 1. Press DISP to check the clock. 2. Press it again to remove it. Turning off the display light 1. Press and hold DISP. 2. Press and hold it again to turn it on. Note , Under the light-off condition, press any keys, the light is turned on and then off automatically if you don't press it within a few seconds. Resetting the unit You can reset the unit when it does not operate properly. 1. Detach the control panel. Refer to page 7 for detaching the control panel. 2. Press the RESET hole with a sharp object. Operating 11 Adjusting the general settings You can adjust [SOUND], [LIGHT] and [OTHER] settings. On the unit 1. Press `. 2. Rotate the volume knob to select [SOUND], [LIGHT], or [OTHER] and press it. 3. Rotate the volume knob to select the item and press it. 4. Rotate the volume knob clockwise or counterclockwise to adjust the level. 5. Press the volume knob to confirm the setting. If you want to return to the previous step, press . On the Remote Control 1. Press and hold FUNC/ • MENU. 2. Press w / s to select [SOUND], [LIGHT], or [OTHER] and press ENTER. 3. Press w / s to select the mode and press ENTER. 4. Press w / s to adjust the level. 5. Press ENTER to confirm the setting. If you want to return to the previous step, press . For [SOUND] setting You can adjust sound quality by adjusting the level of BASS (bass), MID (middle), TRB (treble), BAL (left/ right speaker), FAD (front/rear speaker) and S--W (Sub-woofer: optional). • When you set the EQ to USER 1/2 mode: You can adjust the level of BASS (bass), MID (middle), TRB (treble) BAL (left/right speaker), FAD (front/rear speaker) and S--W (Sub-woofer: optional). • When you set the EQ except USER 1/2 mode: You can adjust the level of BAL (left/right speaker), FAD (front/rear speaker) and S--W (Sub-woofer: optional). For [LIGHT] setting You can adjust the light effects by adjusting DIM, or DIM L. • DIM (Dimmer) OFF/ ON/ AUTO: You can change the brightness of the display window during the power-on status. Settings Description DIM ON The display window becomes dark. DIM OFF The display window becomes bright. DIM AUTO The dimmer operates according to the car dimmer setting. • DIM L (Dimmer Level): When you set DIM to ON/ AUTO, you can adjust the dimmer level. (-2, -1, 0, +1, +2) 3 Operating 12 Operating 3 Operating For [OTHER] setting • AUX (Auxiliary) ON/ OFF It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using a...