Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Kenwood Dateigröße: 1.93 mb Dateiname: Unterrichtssprache:

Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is 3 above, the unit's power be linked to the ignition For that reason, always off the unit's power To link the unit's power (ACC...red) to Installation ¦ Installation Firewall or metal support Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (eg, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) ignition key. — 13 — 13— 13 — —— Installation Installation Removing the hard rubber frame ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then 1 Engage the catch pins on the removal tool and remove the two remove the hard rubber frame. locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the screw (M4.8) on the back panel. English Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) 4 Lower the removal tool out the unit halfway while toward the bottom, and pull pressing towards the inside. Accessory2 Removal tool Be careful to avoid injury from the catch pins 5 Pull the unit all the way out with your hands, being The frame can be removed from careful not to drop it. — 14 — 14— 14 — —— Troubleshooting Guide Troubleshooting Guide just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same cable to the ignition as the battery cable. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. ? The faceplate does not open or close. . The faceplate is incorrectly attached. . Reattach the faceplate correctly, See the section on (page 7). ? The memory is erased when the ignition is turned . The battery wire has not been connected to the proper . Connect the wire correctly, referring to the section on . . The ignition and battery wire are incorrectly . Connect the wire correctly, referring to the section on . ? Even if Loudness is turned ON, for. . Tuner source is selected. . High-pitched tone isn't source. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on . . The cassette tape is bad. . Try playing another cassette tape. If works fine, the first tape was bad. ? The sound quality is poor or distorted. . One of the speaker wires is being pinched by a screw in the car. . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output terminal is connected to a different speaker. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on . The messages shown below display condition. E-77: The unit is malfunctioning for some . Press the reset button on the unit. code does not disappear, consult your nearest service center. 2 3 (Blink): The tape player section . Reinsert the Tape. If the tape cannot the display continues has been properly power and consult — 15 — English English Specifications subject to change without notice. FM tuner section Frequency range (50 kHz Space) ..............87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 30dB) ....................9.3dBf ( 0,8 .V/75 .) Quieting Sensitivity (S/N = 50dB) ...............15.2dBf ( 1.6 .V/75 .) Frequency response ( ± 3.0 dB) ..............................30 Hz – 15 kHz Signal to Noise ratio (MONO) ..............................................70 dB Selectivity ( ± 400 kHz) ...................................................... . 80 dB Stereo separation (1 kHz) ....................................................40 dB AM tuner section Frequency range (9 kHz Space) .....................531 kHz – 1611 kHz Usable sensitivity (S/N = 20dB) .......

Herunterladen

Geben Sie zwei Ziffern: