Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
To cancel this display, press “S” button once. !; ! \ V Volume Press “VOL A” or “VVOL” to increase or decrease volume. —Volume Level W’l nVi'i- ■ rj H1 Oto 40 Press “VOLA” or “VVOL” for more than a half second to sequentially change numeric levels on the display. 3*DSB (3-Dimensional Surround and Super Bass) and Loud Switching © Press 3*D to switch on or off 3*DSB and Loud as follows. 3 DSB OFF 3DSBON 3 DSB OFF LOUD OFF — LOUD OFF LOUD ON t_i (D Press and hold 3»D for more than 2 seconds when 3«DSB is ON, a degree of effect can be selected. Press A VOLV to select one of the 10 degrees (0 through 9). 3*DSB System It is a new sound system combining 3-dimensional sound from two front speakers with rear channel super bass. The 3*DSB employs Spatializer* ICs of Desper Products, Inc. • When 3«DSB is turned on while receiving an AM monaural broadcast or when you are listening to an FM broadcast in monaural mode, you will be able to listen to it with a virtual stereo effect from 4ch speakers. Note: This unit is equipped with anti-volume-blast circuit which serves as an automatic volume level adjuster so that you will not be deafened with sudden loud volume. This system operates as below. When PWR is first pressed to switch on, the volume level is low. After that, the volume level gradually returns to the level when the switch is turned off. Anti-volume-blast circuit is not effective when volume level is lower than position 20 at the display. CQ-DPX105EUC Power and Sound Controls continued ][ I vot1»^-àeîTf' ‘ 'i JüSSÏi i Si —**vji T Attenuator • Press ATT to decrease volume to about 1/10 of the previous level. • Press ATT again to cancel. Changing Audio Modes Press SEL to switch the audio mode in the following order. Normal Mode VOLUME ^ BASS -► TREBLE -► BALANCE I-SUB-W ^ FADER- Bass and Treble • Press SEL to select the BASS (TREBLE) mode. Press "VOL A” or “V VOL” to increase or decrease the bass (treble) response. -12 to +12 -12 to+12 • Press A or V for more than a half second to change numeric levels on the display rapidly. Balance • Press SEL to select the BALANCE mode. Press “VOLA” or “VVOL" to shift the sound volume to the right or left speakers. «WfcüMMM 1 to 15 Balance Center 1 to 15 • Press A or V for more than a half second to change numeric levels on the display rapidly. Fader • Press SEL to select the FADER mode. Press “VOLA” or “VVOL” to shift the sound volume to the front or rear speakers. i 1 to 15 1 to 15 Fader Center • Press A or V for more than a half second to change numeric levels on the display rapidly. Note: When an Audio control mode (BAS/TRE/BAL/FAD/SUB) is selected but no operation is made within 5 seconds (2 seconds at VOL mode), the display will return to the normal operation mode. In such a case, press SEL again to select the control mode. CQ-DPX105EUC Sub-Woofer Volume • Press SEL to select the Sub-Woofer Volume mode. • When Sub-Woofer is activated, press “VOL A” or “VVOL” to increase or decrease the Sub-Woofer Volume level. Sub-Woofer Volume Level -12 to 0 to+12 Sub-Woofer Cutoff Frequency Switching Press and hold SDM (SUB • W * FREQ) for more than 2 seconds to switch the Sub Woofer Cutoff Frequency Switching mode in the following order. SUB -W OFF(MUTE) SUB -W 80Hz * SUB-W 120Hz Selecting Auxiliary Source © Press and hold MODE (AUX) for more than 2 seconds to select AUX Input mode. (D Connect the auxiliary equipment to the AUX Jack. AUX Jack [Canceling AUXInput model Press MODE (AUX) while the AUX mode is operated, the mode will return to the previous mode. Or insert a CD and the mode will change to CD mode. Note: The AUX mode enables setting of VOL, BAS, TRE, BAL, FAD and SUB-W, LOUD, independently from other modes. cn c— 1 J Î B I Caution: In order to insert the plug into the “AUX” Jack properly, make sure to use the correct size of the stereo plug shown on the left. A-MIN1/2" LONG (12mm) B-MAX2/5" DIA. (10mm) C-MIN 1/8" DIA. (3.5mm) CQ-DPX105EUC Power and Sound Controls continued Display Controls Dimmer Switching Press and hold S (S ANALYZER/DIM) for more than 2 seconds to change the brightness of the LCD from one level to another in a cycle of 3 levels as follows: Dimmer 1 — Dimmer 2 -* Dimmer 3 (Bright) (Medium) (Dark) t_1 Spectrum Analyzer Display Switching Press S (S • ANALYZER/DIM) to change the spectrum analyzer display from one spectrum analyzer to another in a total of 6 kinds plus demonstration display mode. SPANA 1 — SPANA2 — SPANA3 — SPANA4 t i Demo Display «- SPANA6 *- SPANA5 Spectrum analyzer 1 Spectrum analyzer 2 Spectrum analyzer 3 Spectrum analyzer 4 Spectrum analyzer 5 -//--ft-l^^mi A\-^ ✓ ••”//' •" // 1 \A Spectrum analyzer 6 CQ-DPX105EUC Radio Basics To change Tuner Mode Press MODE to switch the operation mode in the following order. © Operate from front Panel Tuner ^ CD player ^ CD Changer Control (When a disc is inserted) (When a...