Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
(«• page 23) © Gently press the button of the case and open the cover. Place the face plate into the case and take it with you when you leave the car. Install Removable Face Plate O Fit the face plate with its right or left hole on one of the pins provided on the main unit. © Fit the other hold on the other pin applying slight pressure. © Move the face plate up and down a few times to make sure it is secure. Then close the front panel and press down the right side of the face plate until it clicks into plate. Security Indicator The security indicator blinks when the removable face plate is removed from the unit. Press and hold [SEL] to turn the security indicator on or off. (“LED ON” or “LED OFF”). Lll ©M ; ^^ Default Display Security indicator Law m Blinks LËS OFF - Cautions: • This face plate is not water-proof. Do not expose it to water or excessive moisture. • Do not remove the face plate while driving your car. • Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level. • Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. • If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth. • Do not apply a strong downward force onto the face plate and do not put anything on it while it is open, or it might be damaged. Electrical Connections Cautions: • This product is designed to operate of a 12 V DC, negative ground battery system. • To prevent damage to the unit, be sure to follow the wiring diagram below. • Remove approx.1//' (5 mm) of protective covering from the ends of the leads before connecting. • Do not insert the power connector into the unit until the wiring is completed. • Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables and keep cable terminals free from touching any metal parts. • Remember, if your car has a drive computer or a navigation computer, the data of its memory may be erased when the battery terminals are disconnected. Accessory used for wiring No. Item Q’ty (D Power connector 1 Recommended external amplifier combination (example) • Pre-amp out (rear/front) [CY-M9054 (4 channels system)] • Subwoofer out [CY-M9054 (2 channels system) orCY-M7052 (1 channel system)] □ Wiring Diagram I Redioacx _Subwoofer cord White ™^0N0| Pre-Amp output connector (Front)-Pre-Amp output connector (Rear) — Antenna L (White) R (Red) и CQ-DFX301U Ground lead —= To a clean, bare metallic part of car chassis. Black L-jH-i--—-(§) Power connector pM BATTERY 15À1 Yellow Fuse (15 A) Motor antenna relay control lead CZI= (To motor antenna) (Max. 500 mA) This lead is not intended for use with switch actuated power antenna. Amp. relay control power lead This lead is for connection to the power amplifier Dark blue Gray/black stripe “])p Speaker lead FRONT SPP^REAR SPf Battery lead To the car battery, continuous+12 V DC Power lead —I ACC Red Resistor (1 kO) To ACC power, +12 V DC White/black stripe White (-) (+) Violet/black stripe Violet Left speaker Right speaker (Front) (Front) Left speaker Right speaker (Rear) (Rear) С Q"D F.X5 Qjf/D H4 Oil 7D F,X3Q,1U 25 Electrical Connections icoim) □ Wiring Diagram I CD changer CX-DP88U 4 - ft DIN extension cord (DIN/BATT/RCA/GND) Yellow Fuse (3 A) Battery lead Ground lead® Be sure to connect to a well grounded metallic part of your car because noises or troubles may occur. 1 RCA cord? v-=aXJÇ L- White (L) CD*C-IN h Red (R) Subwoofer cord Red (R) White (L) Red (R) White (L) Preoutcord (rear) Preout cord (front) CQ-DFX501/DF401U CD changer control connector Ground lead — To a clean, bare metallic part of car chassis. Motor antenna relay control lead c i= (To motor antenna) (Max. 500 mA) This lead is not intended for use with switch actuated power antenna. Amp. relay control power lead This lead is for connection to the power amplifier. Gray/black stripe White/black stripe White (-) {+) Black Dark blue © Power connector M BATTERY 15Al=C Yellow Fuse (15 A) Red ~ÄC5~~MI Battery lead To the car battery, continuous+12 V DC Power lead Resistor (1 kO) To ACC power, +12 V DC r Speaker lead FRONT SPFN REAR SP Green/black stripe Violet/black stripe Left speaker (Front) Right speaker (Front) Left speaker Right speaker (Rear) (Rear) Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch power oft. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit yourself because it is dangerous to do so. Troubleshooting Tips □ Common ^ Trouble Cautions: • Do not use the unit if it malfunctions or is something wrong. • Do not use the unit in abnormal condition, for example, without sound, or wi...