Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Sirius Satellite Radio Dateigröße: 1005.47 kb Dateiname: Unterrichtssprache:

Route the antenna cable around and down the window to the lowest point. If your rear window does not have rubber molding, SIRIUS recommends consulting with a professional installer. Route the antenna cable out of the window molding and into the rubber weather stripping around the trunk opening. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. To avoid sharp bends in the cable, run the cable inside of the weather stripping for a few inches, then remove the cable from the weather stripping inside of the trunk. Keep the cable away from hinges, gears, etc., that could damage it. Route the cable out from the rubber weather stripping and along the trunk wall. Continue routing the cable into the cabin through a conduit or along an existing wiring harness. Route the cable through the main cabin area under the interior trim, towards the front of the vehicle. Use the plastic putty knife to lift the plastic trim just enough to tuck the cable under underneath. Avoid side airbag locations on back pillars and above the doors. (Airbag locations are marked with “SRS” logos.) Be careful not to crimp or cut the cable. Bring the cable out from the trim near the firewall and route it under the carpet toward the dashboard or console. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Secure the excess cable with wire ties. Bring the end of the cable out at the SIRIUS radio location. Leave yourself enough cable so you can easily connect it to the antenna connector of the SIRIUS radio or vehicle dock. Pickup Truck Antenna Cable Routing Procedure Figure 5 shows how the antenna cable should be routed from the antenna to your SIRIUS radio in a pickup truck. 1. Route Cable Under Rubber Molding Around Windshield2. Continue Tucking Cable Under Molding To Bottom of Windshield3. Route Cable Out of Molding and Into Weatherstripping Around Door Opening. Continue to Bottom of Door Opening. 4. Bring Cable out from Weatherstripping and Route Under Carpet. 5. Bring Cable Out to SIRIUS Radio Location Follow these detailed cable installation instructions: Use a plastic putty knife or similar tool to lift the rubber molding around the windshield and tuck the antenna cable underneath it. Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner. At the lowest corner of the windshield, route the cable out of the windshield molding and into the rubber weather stripping around the door opening. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Run the cable inside of the weather stripping to the bottom of the door opening. Pull the cable out of the weather stripping at the bottom of the door opening and route it under the carpet toward the dashboard. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Secure the excess cable with wire ties. Figure 5Figure 5 Bring the end of the cable out at the SIRIUS radio location. Leave yourself enough cable so you can easily connect it to the antenna connector of the SIRIUS radio or vehicle dock. SUV/Mini-Van Antenna Cable Routing Procedure Figure 6 shows how the antenna cable should be routed from the antenna to your SIRIUS radio in an SUV or a Mini-Van. 1. Feed Cable Under Rubber Seal Around Hatch Opening3. Route Cable Under Carpet to Dashboard4. Bring Cable Out To SIRIUS Radio Location2. Route Cable Under Interior Trim, into Cabin and Towards Front of Vehicle Follow these detailed cable installation instructions: Feed the antenna cable underneath the rubber weather stripping of the rear tailgate window/door and route the cable along the rear hatch. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Pull the cable out from weather stripping and route it into the cabin under the interior trim. Avoid hinges or gears that could crimp or cut the cable. Route the cable through the SUV’s main cabin area under the interior trim, towards the front of the vehicle. Use a plastic putty knife to lift the plastic trim just enough to tuck the cable under underneath. Avoid side airbag locations on back pillars and above the Figure 6Figure 6 doors. (Airbag locations are marked with “SRS” logos.) Be careful not to crimp or cut the cable. Bring the cable out from the trim near the firewall and route it under the carpet toward the dashboard or console. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Secure the excess cable with wire ties. Bring the end of the cable out at the SIRIUS radio location. Leave yourself enough cable so you can easily connect it to the antenna connector of the SIRIUS radio or vehicle cradle/dock. Convertible Antenna Cable Routing Procedure Figure 7 shows how the antenn...

Herunterladen

Geben Sie zwei Ziffern: