Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Short Circuit Protectio. The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation, correct the problem and turn the head unit off, then back on. The amplifier will reset and play again. Thermal Protectio. To protect the amplifier circuitry against damage caused by prolonged exposure to high temperatures, a thermal protection circuit is activated if the amplifier reaches excessively high operating temperature. Once the thermal circuit is activated, the amplifier will shut down to cool off. The amplifier will automatically turn back on once it cools down to a safe operating temperature. Power Indicato. The diagnostic L.E.D. Illuminates green when the amplifier is on and receiving power. Tri Mode Capabl. If so desired, the amplifier may be run in stereo and mono at the same time. For example, this feature would allow you to run a pair of mid and tweeters in stereo and a sub-woofer mono. Built-in Crossove. The “EL”amplifiers include a built-in variable **high and low pass crossovers. The crossover features a variable frequency selection (60Hz ~ 400Hz) for precise high or low pass filtering. **Except ELA300.1 & ELA / MAA500.1 which have a 40 ~ 120Hz low pass filter. Auxiliary Outpu. The “EL”amplifiers include a auxiliary output for a daisy chain connection of an EL Bazookad Amplified Bass Tube. Power and Speaker Distribution Block. Heavy gauge bare wire distribution blocks are provided for maximum power and signal transfer with minimal resistance. 3 Bass Boos. For added low frequency performance the amplifiers are equipped with a variable 0~12 dB bass boost @ 45Hz. Line Out (ELA150.1, ELA300.1 and ELA / MAA500.1 Only. One set of full range line outputs have been provided for convenient connection to additional amplifiers in the system. Power Fusin. This protects the amplifier against short circuits and excessive current. Remote Turn-o. Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protection. It must be connected with the head unit in order to reset protection circuits. Adjustable Input Sensitivit. Allows you to fine-tune the level matching between your source and the power amplifier. High Level Input ( ELA60.2, ELA / MAA60.4 and ELA100.2. Allowing for integration with “Factory Sound Systems”. Stable To 2 Ohm Stereo Mod. Stability to 2 ohm in stereo mode, 4 ohms bridged. The ELA150.1, ELA300.1 and ELA/ MAA500.1 are stable to 2 ohms mono. 4 MOUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well as a gas tank in the automobile. Make sure you know where they are when mounting the amplifier to avoid puncturing lines, shorting wires or drilling holes in the gas tank. Once you are ready, use a pencil to mark the mounting holes in the bottom panel. After you have marked the locations of the holes move amplifier out of the way and drill small starter holes to make the tapping screws easier to install. Use provided screws to tighten down the amplifier. 5 POWER BASS B...
Dieses Handbuch ist für folgende Modelle:Car-Receiver - ELA150.1 (4.25 mb)
Car-Receiver - MAA60.4 (4.25 mb)
Car-Receiver - ELA300.1 (4.25 mb)
Car-Receiver - ELA500.1 (4.25 mb)