Stimmen - 6, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
theft, disconnecting the car battery), the set is electronically blocked. Then it may only be used again after the appropriate code number has been entered (see car radio passport). Wrong code number entered It should not be possible for thieves to ascertain the code number by trial-and-error. This is why the set will be blocked for a certain period of time, if an incorrect code number is entered. In this case, “---” will appear in the display. This waiting time is 10 seconds after the first three attempts, and 1 hour following subsequent attempts. After 19 unsuccessful attempts, “OFF” will appear in the display and the set can no longer be restarted. Note: Keep you car radio passport with the code number in a safe place in order to avoid “unauthorized access” to your car radio. If the power supply to the radio is interrupted while the code system is switched on, you need to know the right code number. The radio will operate again as soon as you have entered the right code number. If you lose your radio passport and have forgotten your code number, you will not be able to restart the set after the power supply has been interrupted. In this case, your radio can only be reset in our central customer service workshop or in one of our service agencies abroad. Switching the code system on Precondition: The radio must be connected to permanent power. In order to switch the code system on: • Turn the radio off. • Hold down the preset buttons 1 and 4 simultaneously. • Turn the radio on. “Cod” briefly appears before the radio begins to operate. • Release preset buttons 1 and 4. The code system is on. “Cod” will be briefly displayed each time the radio is turned on. Amplifier Section Restart following interruption of power supply (Code system switched on) • Switch on the set. “Cod” will appear in the display. • Briefly press preset button 1, “000” will appear in the display. • Enter the code number given in the Blaupunkt car radio passport: Preset button 1 only allows to choose “0” or “1”. The first “0” will not be displayed. Example: the code number is 0521. -Press preset button 1 until “000” ap pears in the display. -Press preset button 2 five times, “500” appears in the display. -Press preset button 3 twice, “520” appears in the display. -Press preset button 4 once, “521” appears in the display. • To confirm the code number: Press the upper part of the rocker switch . Your car radio is now ready for operation. If three dashes appear again in the display, you have entered a wrong code number. Now it is essential to enter the correct code after the waiting period has elapsed (Cod in the display). If the radio is turned off before the waiting period has elapsed, then the waiting period restarts as soon as the radio is turned on again. Switching the code system off • Turn off the radio. • Simultaneously press preset buttons 1 and 4 and hold them down. • Turn the set on. “Cod” will appear in the display. • Enter the code number given in the Blaupunkt car radio passport and confirm: See example “Restart following interruption …”. The code system is now deactivated. ON/OFF To switch on the set: • Turn button 1 clockwise. To switch off the set: • Turn button 1 counterclockwise. Bass and Treble Control Bass Control To adjust the low frequencies: • Press the AUD button 2. Display 9 gives you bas plus a number between -7 and +7. • Press rocker switch 7 on the right to boost the bass frequencies or on the left for bass reduction. The number on the display 9 changes between -7 and +7. Treble Control To adjust the high frequencies: • Press the AUD button 2 until tre and a number between -7 and +7 appears on the display. • Press rocker switch 7 on the right to boost the high frequencies or on the left for treble reduction. The number on display 9 changes between -7 and +7. ENGLISH 15 Balance and Fader Control Balance control To balance the sound level left/right: • Press the AUD button 2 until bal is shown on the display. Press rocker switch 7 on the left or right to adjust the sound impression according to your personal preferences. Display 9 gives you a number between -9 and +9. Fader control To balance the front/rear sound level: • Press the AUD button 2 until fad is shown on the display. Press rocker switch 7 on the left or right to adjust the sound impression according to your personal preferences. Display 9 gives you a number between -9 and +9. Note: If the rocker switch < > is kept depressed (on the left or right), the set quickly advances to the final values (+7/+9 or -7/-9) or to the “0” position. Radio Section Selecting a Station With your car radio you can select stations from the FM (ultra-short wave) and FM-Travelstore level. To select FM, • press the FM•T button 3 briefly. “FM” lights up on display 9 a. To select FM-Travelstore, • press the FM•T button 3 briefly until “FM•T” is shown on display 9 b. For more information on this function see chapter “Automatically Storing the Strongest Stations”. Tun...