Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Backward Track Select cn will only go back to the beginning of the track in play. The Random Play mode can be cancelled by pressing the button again (.RANDM“ indication will disappear from the display panel) or by activating the Intro-Scan cqor Repeat Play cr functions. ct DISC EJECT ( ) Disc play is stopped, the disc is ejected and the unit will change to radio operation by pressing this button. If the disc is not removed from the unit within 10 seconds of being ejected, it will automatically be re-loaded into the unit to prevent damage ( DISC will appear on the display panel). Pressing the CD Mode Selector button cl again before removing the disc will also re-load the disc into the unit. cu TIME/FREQUENCY DISPLAY SELECTOR (DISP) Press this button to call the time display on the incorporated quartz clock. Press the button again to return to radio frequency or disc display. dl THEFT-DETERRENT L.E.D. Located on the chassis behind the front panel, a light-emitting diode (L.E.D.) will flash when the panel is removed. The flashing light serves as a visual warning to the would-be thief that the unit has been disabled by removal of the front panel. dmRE-SETBUTTON A Re-Set button is located on the front of the chassis (front panel must be removed to access the button). The re-set circuitry is provided to protect the microprocessor circuitry and should only be activated under the following circumstances as it will erase the time and radio station pre-set memories. 1. Upon initial installation after all wiring is completed. 2. After the position of the frequency step switch on the bottom of the chassis has been changed. 1414141414OPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONS 128-5272 15 of 20 1515151515OPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONSOPERATINGINSTRUCTIONS SETTING SETTINGSETTINGSETTINGSETTINGSETTINGTHE THETHETHETHETHECLOCK CLOCKCLOCKCLOCKCLOCKCLOCK 1. Turn the radio on so that the radio frequency or clock time is shown on the display panel. 2. Press and hold the Time/Frequency Display Selector button cu approximately 2 seconds until the time display begins flashing. 3. While continuing to hold the Time/Frequency Display Selector button, press the Down Seek Tuning button ( )bp to adjust the hours and the .PM“ indicator and the Up Seek Tuning button ( ) bo to adjust the minutes to the correct time. 4. When the correct time is shown on the display panel, release the Time/Frequency Selector button. ERROR ERRORERRORERRORERRORERRORCODES CODESCODESCODESCODESCODES If a problem should develop while operating the CD player, the following error codes may be displayed on the display panel: ER 1: Indicates the disc is not loading or ejecting properly. Try re-loading or pressing the Eject button again. Check the condition of the disc in use or try another disc. ER 2: Indicates an interface error between the disc mechanism and radio circuitry. Press the Re-Setbutton dm andtryagain. ER 3: Indicates an error in the laser reading the disc. Eject the disc, make sure it is clean, undamaged, and loaded correctly (label side up). Re-load the disc and check for proper operation or try another disc. RST: Indicates a system error. Press the Re-Set button dm and try again. ROM: Indicates that a computer CD-ROM has been loaded into the unit. Eject the disc and load an audio CD. If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance. 3. If there is a malfunction of any of the switches on the unit or of the CD player, pressing the Re- Set button may clear the system and return to normal operation. dnFRONTPANELRELEASEKNOB This knob is used to release the mechanism that holds the front panel to the chassis. To detach the front panel, slide the button to the right so that the left side of the panel is released. Grasp the released side and pull it off of the chassis. To reattach the panel, position the right side of the panel in place first and then press the left side of the panel until the mechanism locks it into place. DETACHING THE FRONT PANEL Release Button NOTES ON USE OF FRONT PANEL 1. Make sure the front panel is right-side-up when attaching it to the chassis as it cannot be attached when up-side down. 2. Do not press very hard on the front panel when attaching it to the chassis. No more than light to moderate pressure should be needed. 3. When attaching the front panel, make sure the right side is correctly engaged before pressing the left side to lock it into position. 4. When taking the front panel with you, please use the supplied carrying case to protect the panel from dirt and damage. ATTACHING THE FRONT PANEL Engage right side first 128-5272 16 of 20 SPECIFICATIONS SPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONS Size: Operating Voltage: Output Power: Output Wiring: Output Impedance: Low-Level Output: Tuning Range: Sensitivity: FM Stereo ...