Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
THE FM TRANSMITTER OPTION MUST BE SET TO ”FM ON” IN THE SHUTTLE USER MENU. (REFER TO THE OWNER’S MANUAL, PUBLICATION NO.128-7193.) 2. IF THE SIR-CK3 IS INSTALLED USING THE WIRELESS FM SWITCHING BOX, SAT-SWB, OPTION, DO NOT CONNECT THE AUDIO CABLE TO THE LINE OUT CONNECTOR OF THE CRADLE. SHUTTLE ANTENNA TO VEHICLE +12 VDC POWER RECEPTACLE VEHICLE RADIO ANTENNA VEHICLE FM RADIO WIRELESS FM SWITCHING BOX SAT-SWB (PURCHASED SEPARATELY) TO VEHICLE RADIO ANTENNA JACK OPTIONAL AUDIO CABLE (PURCHASED SEPARATELY) 128-7194 9 of 20 -9- CAUTION: Do not install the mounting base on a leather or fabric surface, or in a position that could impair your vision, block air bag(s) or obstruct vehicle dashboard controls and/or radio CD/casette operational displays. NOTE: The adhesive backing on the base will not permit easy repositioning once it has been mated to the surface; use extreme care and planning when selecting the mounting location. If the base is to be screwed to the surface, make sure the area in back of the mounting surface is clear of wires or other items to prevent unintentional damage. c. Using the alcohol swab supplied with your kit, clean the mounting surface and thoroughly wipe the area dry with a clean lint-free cloth. d. The cradle contains a rear mounting plate After deciding the mounting configuration, loosen and remove two flat-head screws securing the plate to the cradle and remove the plate. Save the two screws for reassembly. FLAT-HEAD SCREWS (2) REAR MOUNTING PLATE CRADLE ASSEMBLY (REAR VIEW) BASE ASSEMBLY MOUNTING SCREW HOLES (4) FOR DIRECT HARD MOUNTING e. If the outside air temperature is cold, it may be beneficial to warm the adhesive backing on the base using a portable hair dryer, or by holding the backing surface in front of a vehicle heater vent. f. Remove the plastic liner from the adhesive backing on the base, and fix the base in position on the surface; make sure the mounting pad is accurately positioned on the first try, since repositioning may be difficult, if not impossible. g. If the mount is to be screwed in place, do not remove the plastic liner from the adhesive backing. Use appropriate sheet metal or machine screws for this purpose. MOUNTING BASE ASSEMBLY PLATE MOUNTING PLATE PLASTIC LINER AND ADHESIVE BACKING -10128- 7194 10 of 20 NOTE: Allow a 72-hour period for the adhesive backing to cure completely. 3. Installing the Cradle Using Double-Sided Tape You can mount the cradle directly to your dashboard or other flat surface without using the cradle mount in the kit. To do this, do not remove the mounting plate assembly from the cradle. a. Remove the 3/4” x 3” double-sided tape from the supplied kit. b. Determine the location of the cradle, and clean the mounting surface as before. c. Peel the backing from one side of the tape, and press the tape in place on the rear or bottom cradle mounting plate. -11 d. Peel the backing from the exposed side of the tape and carefully position the cradle on the mounting surface, gently pressing the cradle into place. 4. Using Other Manufacturer’s Mounts The Shuttle Cradle can also be installed using other manufacturer’s mounts; the mounting plate provisions on the rear or bottom of the cradle provide you with multiple mounting options within the vehicle using various vehicle-specific aftermarket brackets, such as those purchased separately from Panavise, Pro-Fit, etc. 5. Installing the Shuttle into the Cradle Install the shuttle as follows: a. Carefully line up the shuttle rear spine grooves with the cradle guide spines; slide the latch tab lever to the unlock ( ) position, and lower the shuttle into the cradle. 128-7194 11 of 20 128-7194 12 of 20 b. After making sure the connectors are properly lined up, gently press down on the shuttle to mate the connectors together. c. Slide the latch tab lever to the lock ( ) position; the tab will enter the shuttle latching tab recess to prevent vertical movement. The shuttle should now be nestled securely in the cradle. -12- 20-PIN SYSTEM CONNECTOR CRADLE FRONT VIEW CRADLE TOP VIEW LATCH TAB LOCK/UNLOCK LEVER SHUTTLE LATCHING TAB CRADLE GUIDE SPINES CONNECTOR GUIDE PIN CRADLE REAR VIEW SHUTTLE REAR VIEW SHUTTLE REAR SPINE GROOVES SHUTTLE LATCHING TAB RECESS LATCH TAB LOCK/UNLOCK LEVER 128-7194 13 of 20 -13- 6. Sirius Program Listening Options The Shuttle and Cradle provide an audio output signal in three manners: 1. When using the SIR-CK3 cradle with the FM switching box option, the audio signal can be transmitted to a car radio on one of over 100 selectable FM frequencies using the menu options included in your PNP3 shuttle. (Refer to the shuttle owner’s manual.) The audio signal can then be played through your car radio when the car radio is tuned to one of these frequencies. 2. In this instance, use of a hard-wired FM transmitter, such as the optional FM Switching Box assembly (Part No. SAT-SWB) is available and provides a hard-wired FM output when connected to the FM OUT connector on the left rear side...