Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Protect from High Temperatures Exposure to direct sunlight for an extended period of time can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback. Do not mount radio within close proximity of engine compartment. Use the Proper Power Supply This product is designed to operate with a 12 volt DC negative ground battery system. Protect the Disc Mechanism Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit. CAUTION: THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/ INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY. BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. PLEASE REFER SERVICING TO A QUALIFIED TECHNICIAN. WARNING: • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO WATER. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. • THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION. 2 VR182 DISC NOTES Depending on the recording status, conditions of the disc, and the equipment used for recording, some CD- Rs/ CD-RWs may not play on this unit. For more reliable playback, please NOTE: A disc may become scratched (although not enough to make it unusable) adhere to the following recommendations: depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player. • Use CD- RWs with speed 1x to 4x and write with speed 1x to 2x. • Use CD- Rs with speed 1x to 8x and write with speed 1x to 2x. • Do not play a CD- RW which has been written more than 5 times. Compatible Disc Types Table 1: General Disc Information Disc Type Logo Diameter/ Playable Sides Playback Time Audio CD REWRITABLE RECORDABLE 12 cm single side 74 minutes NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and the CD is finalized. Disc Maintenance • A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge. Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent. Insert label Do not bend. Never touch Wipe clean fromside up. the under side the center to the of the disc. edge. • Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction. • Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers. • Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle. 3 VR182 4 INSTALLATION Before You Begin 1. Disconnect Battery Before you begin, always disconnect the battery negative terminal. 2. Remove Transport Screws and discard. Important Notes • Before final installation, test the wiring connections to make sure the unit is connected properly and the system works. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle. • Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop. • If the installation angle exceeds 30. from horizontal, the unit might not give optimum performance. • Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration. DIN Front Mount This unit can be installed in a dashboard with an opening of the following dimensions: 1. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is locked into position, use the removal keys (supplied) to disengage it. Insert the keys through the holes in the front panel as far as they will go, and then slide the sleeve off the back of the unit. 2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis. 3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward a...