Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
2 RADIO OPERATION ................................................ 3 TAPE PLAYBACK ..................................................... 5 AUXILIARY EQUIPMENT ......................................... 6 MAINTENANCE ........................................................ 6 SPECIFICATIONS .................................................... 7 Note Some buttons are assigned two or more functions. For detailed descriptions, refer to the related pages. Notes on cassettes Do NOT expose cassettes to direct sunlight, extremely high or cold temperature or moisture. Keep cassettes away from equipment with built-in magnets to avoid unwanted noise or loss of sound quality. Do NOT touch the tape of a cassette, as any dirt or dust will contaminate the heads. Be sure to remove any cassette from the unit if you are not using it. Caution on the transit protection pad Be sure to remove the pad before operating the unit. Transit protection pad 1 11 ENGLISH ENGLISHENGLISH THEFT PROTECTION Take the front panel with you when leaving the car, and keep it in the supplied carrying case. Detaching the front panel Before detaching the front panel, remove the cassette to prevent possible damage to the unit. 1 Press zto remove the cassette. 2 Press and hold PWR/MUTE until the unit turns off. 3 Press %. (Hold the panel with one hand to prevent accidentally dropping it.) 4 Remove the panel. Attaching the front panel 1 Engage the left side of the front panel to the left catch on the unit. 2 Push the panel forward until it locks. Be sure not to press any buttons while you are attaching the panel. Note Do not touch the front panel connector. This could cause a poor or faulty connection. Security lamp The security lamp will continue to flash while the front panel is detached from the unit. BASIC OPERATION, AUDIO AND CLOCK ADJUSTMENT Smart Jog Turning the unit on/off • Press PWR/MUTE to turn on the unit. The unit also turns on when you insert a cassette. • Press and hold PWR/MUTE until the unit turns off. Note Most operations described in this manual require the unit to be turned on before starting the operation, unless explicitly stated otherwise. Changing the source mode 1 Press FNC. Pressing FNC cycles through source modes in the following order: FM1 FM2 FM3 AM1 AM2 * Tape Play mode (available while a cassette is in the unit) Adjusting the volume 1 Turn the Smart Jog. VOL (volume) indicator flashes. Muting the sound 1 Press PWR/MUTE briefly. To restore volume, briefly press PWR/MUTE again. ENGLISH ENGLISH ENGLISHENGLISH 2 22 Adjusting sound You can select the following modes for adjusting sound depending on the music you listen to: BASS (low frequencies), TRE (high frequencies), BAL (left/right), FAD (front/rear) and H-BASS (high bass) 1 Press SEL repeatedly to select the mode to be adjusted. Pressing SEL cycles through the modes. The selected mode’s indicator flashes (except for HBASS). 2 Turn the Smart Jog to increase or decrease the level for the selected mode (except for H-BASS). In H-BASS mode, turn the Smart Jog to select on or off. Note Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. Aligning the source levels (Source Level Adjuster) Volume may vary each time you change the source mode. In this case, you can align each source mode’s volume to almost the same level. 1 PressFNC repeatedly to select the desired mode. 2 Press DISP while pressing SEL. “LA 0” appears in the display. 3 Turn the Smart Jog to adjust the level. Note Adjust the level within 5 seconds, or the selected mode will be canceled. Restoring the factory settings 1 Turn off the unit. 2 Press and hold DISP until “LA --” appears in the display. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. Muting button beep sounds 1 Turn off the unit. 2 Press and hold SEL until “BEEP” appears in the display. 3 Turn the Smart Jog to select on (level indicators appear) or off (level indicators disappear). 4 Press and hold SEL until the unit turns off. Setting the clock 1 Press DISP to have the clock displayed. If the clock indication is already displayed, skip this step. 2 Press and hold DISP until the clock indication flashes in the display. 3 Press TUNEi (to set hour) or TUNEk (to set minute) and turn the Smart Jog. 4 Press DISP. Displaying the clock 1 Press DISP. To return to the former display, press DISP again. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) Band indicator Local indicator Stereo indicator Frequency indication 1 Press FNC repeatedly to select the desired band (FM1, FM2, FM3, AM1 or AM2). 2 Press TUNEi(to move to higher frequencies) or TUNEk(to move to lower frequencies) to tune in to a station. “ST” appears in the display when an FM station is broadcasting in stereo, and receiving conditions are good. Seek Tuning and Manual Tuning • Press and hold TUNEi or TUNEk until Seek Tuning starts. The unit locates a station automatical...