Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Installation Measurements IN-DASH MOUNTING FOR GM VEHICLES Figure 2. Typical Mounting using Metal Mounting Adapter Figure 4. Top Mount using Plastic Mounting Adapter. Figure 5. Bottom Mount using Plastic Mounting Adapter. Machine Self . Tapping Screws Plastic Figure 3. Typical Mounting using Plastic Mounting Adapter Figure 6. Bottom Mount using Metal Mounting Adapter. INSTALLATION FOR FORIEGN VEHICLES INSTALLATION FOR DOOR MOUNT Figure 7. Rear Deck Mount for Volkswagen Golf I Figure 10. Marking Holes Figure 11. Cutting and Drilling Holes Figure 8. Front Dash Mount for S-Series Mercedes Figure 12. Installing Speakers USE TEMPLATE PROVIDED TO CORRECTLY ALIGN SPEAKERS. MARK WITH CHALK OR PENCIL. USE 1/8" DRILL BIT FOR SCREW HOLES INSTALL C-CLIPS AND MOUNT SPEAKERS WITH SCREWDRIVER. CAREFUL" Figure 9. Front Dash Mount for Fiat GENERAL WIRING DIAGRAM RIGHT FRONT SPEAKER HP40.4 HP46.4 HP52.4 HP64.4 HP65.4 HP68.4 HP692.4 HP693.4 VIOLET/ BLACK (-) ANTENNA INPUT CD CHANGER (DIN CABLE) FRONT RCA OUTPUT TO POWER AMPLIFIER (GRAY) REAR RCA OUTPUT TO POWER AMPLIFIER (GRAY) ■T (GROUND) BLACK LEFT FRONT SPEAKER HP40.4 HP46.4 HP52.4 HP64.4 HP65.4 GREEN (+) TO POWER ANTENN REMOTE POWER AMPL TRIGGER BLUE HP68.4 HP692.4 HP693.4 GREEN/ BLACK (-) LEFT REAR SPEAKER RIGHT REAR SPEAKER SPEAKER WIRING FOR USE IN 4-CHANNEL OPERATION. Cousticf CAR AUDIO INSTALLATION INSTRUCTIONS MODEL: HP46.4 4” X 6” Two-Way Figure 13. 4-Ohm Connection. Coustic Car Audio 7676 South 46th Street, Suite 2020 Phoenix, AZ 85040 ©2000 COUSTIC is a registered trademark of the Mitek Corporation All Rights Reserved. #21A3972 Congratulations... On your purchase of our Coustic speakers engineered specially for use in automotive environments. Over the years these Coustic speakers will give you countless hours of unparalleled listening pleasure while you are on the road. However, to ensure that your Coustic speakers perform at their highest level of efficiency, read the instructions thoroughly and follow the precautionary steps and instructions as listed. That done, you will then have superb sound reproduction from speakers designed specifically by Coustic for use in automobiles. But Coustic does not just manufacture automotive speakers, we also build innovative power amplifiers, high performance subwoofers, state-of-the-art real-time analyzers and esoteric electronic crossovers. In other words, everything you need to create the ultimate car audio. SPECIFICATIONS INSTALLATION PREPARATIONS AND PRECAUTIONS 1. Make sure car audio system is turned off before speaker installation begins. 2. Metal clips and filings should be kept away from speakers; WORK AS CLEANLY AS POSSIBLE. 3. Install each speaker as firmly as possible. To maximize high frequency reproduction, make sure there is no obstruction between speaker and interior of the vehicle. 4. Make sure speaker cone has sufficient breathing room. 5. Speakers must be wired IN PHASE to produce the best sound fidelity. Double check audio system for correct phasing (i.e., 6. Before doing any cutting or drilling, check all clearances and mounting locations again. Check position of both speakers (not just one) in case car doors are not symmetrical (e.g., multiple electric window controls on the driver's side only). INSTALLATION The HP46.4 is designed to fit European and GM vehicles without extra adapters. Refer to the different installation applications outlined in this instruction. Power Frequency Sensitivity Input Handling Response (1 watt, Impedance (watts) (±5dB) 1 meter) HP46.4 65 watts 58-20k Hz 90 dB SPL 4 Ohms...