Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Audiovox
Dateigröße: 179.89 kb
Dateiname: a64c7935-fe03-4c63-805c-b8b9f0fe9df6.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Just pick a reasonably flat panel, drill a few holes, fasten a few screws, and you’re listening to stereo. INSTALLING OVAL SPEAKERS IN REAR DECKS OR FLAT SURFACES Most cars are factory-equipped with speaker openings in the rear deck (package shelf). By examining the underside of this panel, using trunk access, you will probably find at least one (usually two) oval-shaped holes in the steel underliner of the rear deck. The size of these holes vary with the make of car, but the most common openings are for 6”x9”, 5”x7”, and 4”x10” speakers. Occasionally, you’ll find a 5” or 5-1/4” round hole. Selecting the Speaker Location Use the following guidelines to select the speaker location: 1. Examine the deck panel thoroughly. Observe movement of the trunk springs, trunk lid, support hinges, power antenna, etc. Obviously, you don’t want to install a speaker where the arc of a moving trunk support would interfere with the speaker grille. Avoid all areas that might cause interference with the normal functions of the trunk lid and/or antenna assembly. CAUTION: Even professional installers have mounted a speaker and then found out it interfered with some moving part. 2. Check the speakers you have purchased against the existing holes in the steel sub-liner by placing the speaker against the -4 bottom of the opening and check that the speaker matches the shape of the existing cut-out. Also check that the four speaker mounting holes align with the four existing holes in the steel sub- liner. Cutting Speaker Opening Prepare the speaker opening as follows: NOTE: This procedure can also be used for any flat panel install (Wagons, Vans, etc.) that have sufficient space behind the panel for recessing the speaker. (The panel must be removable or accessible from behind.) 1. Provided that all holes align, place speaker aside and proceed to cut out the oval opening in the fiber panel that covers the existing hole in the steel sub-liner. NOTE: It is easier to cut the opening if you use a sharp serrated steak knife in a sawing motion. Use care not to over-cut the hole size by periodically checking the speaker grille. 2. Once the speaker openings have been cut, pierce the four speaker mounting holes and enlarge them to a diameter of 3/16”. Grille Installation Inspect the grille included with the speaker. If the grille contains existing threaded studs projecting from it , skip this section. If the grille contains four threaded holes in it, locate the threaded rods included with the speaker and screw them firmly into the holes in the grille. The third grille type contains four holes for use with four screws. Proceed with grille installation as follows: Speaker Cutting Detail 1. Place grille on top of package shelf, allowing the studs to protrude through the holes you previously punched. 2. Place the speaker below the shelf and align it over the four studs of the grille. Secure the speaker using four speed clips included. If the grille requires screws and nuts, insert the screws from the top of the rear deck, and through the grille and speaker; secure grille and speaker with hex nuts. 3. Repeat entire procedure for remaining speaker. 4. Wire speakers per instructions for your stereo system. -5 MESH GRILLE MESH GRILLE Speaker Mounting Details The following illustrations define the requirements for mounting the speaker on the near and far sides of the mounting surface or independent mounting board. FACTORY SPEAKER REPLACEMENT FACTORY GRILLE SPEAKER EXISTING FACTORY HARDWARE MOUNTING SURFACE MESH GRILLE APPLY BUTYL PUTTY (4 PLACES) MACHINE SCREW GRILLE MOUNTING SURFACE SPEAKER NUT TYPICAL SPEAKER INSTALLATION APPLY BUTYL PUTTY (4 PLACES) SHEET METAL SCREW SPEAKER GRILLE MOUNTING SURFACE SPEED CLIP -6 This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s) or markings. THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, accessories, or vehicle electrical systems. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL...