Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
cable to other Krell components and to other devices 10 S-Video Output that incorporate 12 V power on/off trigger input. One S-Video output with a DIN connector. When the KID is in the operational mode and a trig- ANALOG OUTPUTS ger is enabled, the 12 VDC Out provides 12 V of DC 11 Single-ended Audio Outputs output. When the KID is in the stand-by mode or off, Two single-ended analog audio channel outputs or if a trigger is not enabled, the DC output is 0 V. with RCA connectors. POWER CONNECTION 12 Balanced Analog Audio Outputs 15 IEC Connector Two balanced analog audio channel outputs with A standard male IEC power connector, for use with XLR connectors. the AC power cord. REMOTE CONNECTIONS 13 Comm Port RS-232 Connector Sends software updates directly to the KID using an external computer control system. Krell / Papa Dock 7 Connecting the Papa Dock to Your System AC Power Guidelines for the Papa Dock Papa Dock Back Panel Connections CONNECTING TO YOUR SYSTEM, continued Connect the Papa Dock to Your System With the KID docked onto the Papa Dock: 1. Connect the loudspeaker cables to the Papa Dock amplifier channel output binding posts (16) located on the back panel. The binding post terminals accept spade lugs, bare wire, or pins. Use the red terminal for the positive connection and the black terminal for the negative connection. IMPORTANT: Tighten loudspeaker binding posts by hand only. 5. Plug the AC power cord into the amplifier’s IEC connector (21). 6. Plug the other end of the AC power cord into the AC wall outlet. The amplifier is now ready for operation. AC Power Guidelines for the Papa Dock. Krell recommends operating the Papa Dock amplifier from a dedicated 15-amp AC power line. Please contact your Krell dealer, distributor, or Krell before using any devices designed to alter or sta- bilize the AC power for the Papa Dock. FIGURE 7 Papa Dock Back Panel Connections LEFT OUTPUT RIGHT OUTPUT RS-232 IN 12VDC OUT 30 mA MAX. COMPOSITE S-VIDEO VIDEO OUT PAPA DOCKPAPA DOCK KRELL INDUSTRIES, INC. 45 CONNAIR ROAD ORANGE, CT 06477-3650 USA 50/60 Hz NO USER SERVICEABLE PARTS INSIDE MADE IN USA 16 171819 20 16 21 AMPLIFIER CHANNEL OUTPUTS 20 12 VDC Out 16 Left and Right Outputs Sends a 12 V power on/off signal via a 12 V trigger Two channel outputs via 5-way binding posts. cable to other Krell components and to other devices that incorporate 12 V power on/off trigger input. VIDEO OUTPUTS 17 Composite Video Output When the Papa Dock is in the operational mode and One composite video output with an RCA connector. a trigger is enabled, the 12 VDC Out provides 12 V of 18 S-Video Output DC output. When the Papa Dock is in the stand-by One S-Video output with a DIN connector. mode or off, or if a trigger is not enabled, the DC output is 0 V. REMOTE CONNECTIONS 19 Comm Port RS-232 Connector POWER CONNECTION Sends software updates directly to the KID using an 21 IEC Connector external computer control system. A standard male IEC power connector, for use with the AC power cord. 8 Krell / Papa Dock Insert the iPod-device into the KID Dock Connector Power LED Color Guides Operation FIGURE 4 Inserting the iPod-device Into the Dock Connector POWERBASSTREBLEVOLUMEAUXINPUT4 1 INSERT THE IPOD-DEVICE INTO THE KID DOCK CONNECTOR 7 When the KID or the Papa Dock are plugged into AC power, connect the iPod-device: 1. Hold the iPod-device in both hands as shown in the illustration above, using the iPod-device support (1) as a guide. KID Power LED Color Guide. When the KID is plugged into AC power, the power LED illuminates as follows: Red The KID is in stand-by mode. Blue The KID is on, in the operational mode, indicating that an iPod-device is connected. Purple The KID is on, in the operational mode, and an iPod-device is not connected. 2. Center the iPod-device connector against the KID dock connector (4). 3. Push down on the top of the iPod-device gently but firmly until its connector plugs into the KID dock connector. Papa Dock Power LED Color Guide. When the Papa Dock is plugged into AC power, the power LED on the front panel illuminates as follows: Red The Papa Dock is in stand-by mode. Blue The Papa Dock is on, in the operational mode, when the KID is connected to the Papa Dock and the iPod-device is inserted into the KID dock connector. OPERATION When the iPod-device is connected to the KID, you are ready to play music. When the KID is connected to the Papa Dock and an iPod-device is inserted into the KID dock connector, the KID powers on the Papa Dock. 1. Press the play key (33) on the remote. 2. Adjust the volume (27) using the buttons on the KID front panel or the keys on the remote. Numerical values indicating the volume level appear in the display window. 3. Adjust the bass tone control (25) using the buttons on the KID front panel or the keys on the remote. Numerical values indicating the bass tone level appear in the display window. 4. Adjust the treble tone control (26) using the buttons on the KID front panel or the ...