Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
EN 7 Play from an external device Through an audio input cable, you can play audio that is transferred from an external audio device, for example, an MP3 player. 1 Connect an audio input cable with a 3.5- mm connector on both ends between • the AUDIO IN socket on this product, and • the headphone socket of an external device. 2 Press SOURCE/SET to switch the product to the AUDIO IN mode. 3 Play audio on the external device (refer to its user manual). 8 Other features Set an alarm timer Note ••Make sure that you have set the clock correctly. 1 Press and hold AL1/AL2 for 2 seconds to activate alarm setting. »»The hour digits blink. 2 Press - TUNE/TIME or TUNE/TIME+ repeatedly to set the hour, and then press SOURCE/SET to confirm. »»The minute digits blink. 3 Press - TUNE/TIME or TUNE/TIME+ repeatedly to set the minute, and then press SOURCE/SET to confirm. 4 Press - TUNE/TIME or TUNE/TIME+ to select an alarm source, and then press SOURCE/SET to confirm. • TUNE: the last listened FM radio station • BUZ: the buzzer 5 Press - TUNE/TIME or TUNE/TIME+ to set the alarm volume, and then press SOURCE/SET to confirm. »»The alarm time and icon are displayed. EN Activate/deactivate alarm timer 1 Press AL1/AL2 to view alarm settings. 2 Press AL1/AL2 again to activate or deactivate the alarm timer. »» The alarm icon appears if alarm timer is on and disappears if it is off. • To stop the ringing alarm, press the corresponding AL1/AL2. »»The alarm repeats ringing for the next day. Snooze alarm When alarm sounds, press SNOOZE. »»The alarm snoozes and repeats ringing nine minutes later. Set the sleep timer This product can switch to standby mode automatically after a preset period. Press SLEEP repeatedly to select the sleep timer period (in minutes). »»When the sleep timer is activated, appears. To deactivate the sleep timer Press SLEEP repeatedly until [OFF] (off) appears. 15 30 60 90 120OFF Adjust display brightness Press BRIGHTNESS repeatedly to select different brightness levels. 9 Product information Note ••Product information is subject to change without prior notice. General information AC Power Model: AS100-050- AA200 Input: 100 - 240 V ~, 50/60 Hz, 0.5 A Output: 5 V 2.0 A Operation Power Consumption < 15 W Standby Power Consumption < 1 W Max. load of USB output 5 V 1.6 A Dimensions - Main Unit (W x H x D) 137 x 62 x 141 mm Weight - With Packing - Main Unit 0.87 kg 0.53 kg Bluetooth Bluetooth specification V2.1 Supported profiles A2DP V1.0, AVRCP V1.0 Range 10 m (Free space) EN Tuner (FM) Tuning Range 87.5 - 108 MHz Sensitivity - Mono, 26dB S/N Ratio < 22 dBf Search Selectivity > 28 dBf Total Harmonic Distortion < 3% Signal to Noise Ratio > 50 dB Amplifier Rated Output Power 2 X 2.5W RMS Speakers Speaker impedance 4 Ohm Speaker driver 1.5'' full range 10 Troubleshooting Warning ••Never remove the casing of this product. To keep the warranty valid, never try to repair the product yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (When you contact the Consumer Care, make sure that the product is nearby and the model number and serial number are available. General No power ••Make sure that the AC power adaptor is connected properly. ••Make sure that there is power at the AC outlet. No sound or poor sound ••Adjust the volume of this product and the connected device. ••Make sure that the Bluetooth connection is valid between your Bluetooth device and this product. Clock setting erased ••Power has been interrupted or the power adapter has been disconnected. ••Reset the clock. EN About Bluetooth device The audio quality is poor after connection with a Bluetooth-enabled device. ••The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them. Cannot connect with the device. ••The Bluetooth function of the device is not enabled. Refer to the user manual of the device for how to enable the function. ••This product is already connected with another Bluetooth-enabled device. Disconnect that device and then try again. The paired device connects and disconnects constantly. ••The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them. ••For some devices, Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of this product. 11 Notice Any changes or modifications made to this device that are not expressly approved by WOOX Innovations may void the user’s authority to operate the equipment. Compliance Notice for the USA and Canada This device complies with Part 15 of the FCC Rules and RSS standard of Industry Canada. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation...