Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The making of unauthorized copies of copy- protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence. This equipment should not be used for such purposes. Note ••The type plate is located on the back of the apparatus. EN 2 Your Bluetooth Speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at Introduction With this speaker, you can enjoy audio from the compatible Bluetooth device or other audio devices. What's in the box Check and identify the contents of your package: • Main unit • 1x AC adaptor • Short user manual • Safety sheet Overview of the main unit efbacd a ON/OFF • Turn on/off the unit. b / • Adjust volume. c • Press to play/pause in Bluetooth mode. d DC IN 5V-1A • Power supply socket. e AUDIO IN • Connect an audio device. f Bluetooth indicator • Steadily on when the speaker is connected with Bluetooth compatible device. • Flashes when disconnected Bluetooth pairing . EN 3 Get started Caution ••Use of controls, adjustments, or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here: Model No. __________________________ Serial No. ___________________________ Connect power This Bluetooth speaker can be powered by either AC power or batteries. Battery power Warning ••Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. ••Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. ••The battery contains chemical substances, so it should be disposed of properly. ••Keep children away from the battery. 1 Open the battery compartment. 2 Insert AA batteries with correct polarity (+/-) as indicated. 3 Close the battery compartment. AC power Caution ••Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back of the speaker. Connect the AC power adaptor to: • the power supply socket on the back of the speaker. • the wall power outlet. DC IN5V . 1A Turn on • Switch ON/OFF on the speaker to the ON positon. »»The Bluetooth indicator flashes (blue). EN Switch to standby mode The speaker switches to standby mode in the following situations. • In Bluetooth mode: deactivate bluetooth connection without audio in cable plugged in. • In MP3 link mode: no audio signal detected over 15 minutes. • The battery level is low. 4 Play Play from a Bluetooth device You can listen to a Buetooth device through this speaker. Note ••The effective operation range between the speaker and your Bluetooth device is approximately 10 meters (30 feet). 1 Switch ON/OFF to turn on the speaker. 2 Press and hold for 3 seconds to activate Bluetooth function on the speaker. »»The Bluetooth indicator flashes. 3 Activate the Bluetooth function in your Bluetooth device (see the device user manual). 4 Select "PHILIPS SBT300" on your device for pairing. »»The speaker gives out 2 beeps and the Bluetooth indicator stays steadily on. • For elder devices, you need to input "0000" as pairing password. 5 Start music play on your Bluetooth device . DoDoPHILIPS SBT3000000PIN 3 sec. EN Play from a PC You can also listen to audio through Bluetooth in PC. Note ••Make sure that you have installed Bluetooth driver in your PC before pairing. ••The steps below are only for windows 7 operating system. If you use other OS/IOS , refer to other OS/ IOS help. 1 Switch ON/OFF to turn on the speaker. 2 Press and hold for 3 seconds to activate Bluetooth function on the speaker »»The Bluetooth indicator flashes. 3 Activate the Bluetooth function in your PC. 4 Add a Bluetooth device in your PC and select "PHILIPS SBT300" for pairing. »»The speaker gives out 2 beeps and the Bluetooth indicator steadily on. 5 Set "PHILIPS SBT300" as default communication device in your PC. 1). Right click the speaker icon ( ) in the lower right corner of the Windows home screen and select "Playback Devices" from the option menu 2). Right click desired speaker and select "Set as Default communnication Device". 6 Start music play on your PC . Play from an external device You can also listen to an external audio device through this speaker. Note ••Your speaker can play under MP3-LINK audio only when the Bluetooth paused or stopped. 1 Connect the MP3-LINK cable to: • the MP3-LINK jack (3.5mm) on the back of the speaker. • the headphone jack on an external device. 2 Start to play on the device. AUDIO IN Control play During play, • press VOL +/- to increase or decrease the volume level. • press to play or pause. »»Available only in Bluetooth mode. ...