Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
iPod/iPhone are different, you may not operate always be careful when performing communication using shielded, and the picture on nearby TV sets may operation method. volume volume dial .on the unit). operate the system from the time the system .The specified station may have temporarily .The USB device is not connected correctly. Turn the iPod/iPhone using buttons on the remote or BLUETOOTH technology. .It may take about 10 seconds before “READING” appears become magnetically distorted. In this situation, Listening to the radio Set the sound EQ . repeatedly. turns on until the playback starts. stopped broadcast. off the system, then reconnect the USB device. unit. In this case, use the control buttons on the .Sony cannot be held liable in any way for damages or other depending on the type of USB device connected. turn off the TV, wait 15 to 30 minutes, and turn it iPod/iPhone. loss resulting from information leaks during communication effect .Do not connect the system and the USB device through a To check the setting Severe hum or noise. There is noise, skipping, or distorted back on. using BLUETOOTH technology. 1 Press TUNER FUNCTION . on the remote or USB hub. sound. The iPod/iPhone cannot be charged. If there is no improvement, move the system far .BLUETOOTH communication is not necessarily guaranteed .When the USB device is connected, the system reads all the press FUNCTION . on the unit repeatedly Tip 1 Press TIMER MENU .. .Move the system away from sources of noise. with all BLUETOOTH devices that have the same profile as files on the USB device. If there are many folders or files on until “FM” appears in the display .. This system is equipped with the DSEE function to reproduce .Connect the system to a different wall outlet. .Turn off the system, then reconnect the USB .If the battery of the iPod/iPhone is empty, the away from the TV. this system. the USB device, it may take a long time to finish reading the clear treble despite degradation caused by compression. 2 Press ./.. repeatedly to select “SELECT,” device. system may not be able to charge it even if .Install a noise filter (not supplied) to the power .BLUETOOTH devices connected with this system must USB device. 2 Perform tuning. The DSEE function is usually activated automatically by and then press .. Cleaning the cabinet cord. .The music data itself contains noise, or the you connect it to the system. In such a case, comply with the BLUETOOTH specification prescribed recognizing the sound source, but it may not be activated .With some connected USB devices, after an operation is Clean this system with a soft cloth slightly recharge it with a computer, etc. then connect it by the BLUETOOTH SIG, Inc., and must be certified to performed, there may be a delay before it is performed by For automatic scanning depending on the function in use. 3 Press ./.. repeatedly to select “PLAY SEL,” sound is distorted. Noise may have been moistened with a mild detergent solution. Do not comply. However, even when a device complies with the .. The remote does not function. entered when creating music data due to the to the system. this system. and then press BLUETOOTH specification, there may be cases where the Press TUNING MODE . repeatedly until use any type of abrasive pads, scouring powder, .Compatibility with all encoding/writing software cannot be .Remove any obstacles between the remote and conditions of the computer. Create the music .Make sure the iPod/iPhone is connected characteristics or specifications of the BLUETOOTH device guaranteed. If audio files on the USB device were originally “AUTO” appears, and then press TUNING +/. To cancel the timer the remote sensor . on the unit, and position data again. securely. or solvents, such as thinner, benzine, or alcohol. make it impossible to connect, or may result in different encoded with incompatible software, those files may .. Scanning stops automatically and “ST” (for Setting the speaker light Repeat the same procedure as above until “OFF” the unit away from fluorescent lights. .The bit rate used when encoding the files was control methods, display or operation. produce noise or interrupted sound, or may not be played stereo programs only) light up in the display . The iPod/iPhone cannot be recognized. .Noise may occur or the audio may cut off depending on appears in step 3, and then press .. .Point the remote at the system’s remote low. Send files encoded with higher bit rates to back at all. the BLUETOOTH device connected with this system, the when a station is found. illumination .Disconnect the power cord and reconnect it after .This system cannot play audio files on the USB device in the sensor .. the USB device. communications environment, or surrounding conditions. To change the setting the STANDBY indicator . is turned off. Then following cases; You can set a speaker light illumination from a .Move the remote closer to the system. .when the total number of audio files in a folder exceeds St...