Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Please read through these operating instructions before using your speaker system to optimize performance. • This speaker system has an impedance of 8 ., and should be connected only to an amplifier designed with a load impedance of 8 . (the amplifier ’s speaker output connector should clearly be labeled “8 .“). • In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions: -Be sure to turn the connected devices off and remove the power cord from the wall outlet beforehand when changing the connection or installation method. -Do not use excessive amplifier volume if using a tone control to emphasize high or low frequencies. • Do not use the speaker to output distorted sound for long periods of time. This can result in a fire hazard. INSTALLATION PRECAUTIONS • Do not install these units near a stove or other heating appliance, or put them in a place exposed to the sun. Such locations may cause the cabinet to change color and the speaker system to break down. • Do not attach the front speakers to the wall or ceiling. It may fall off and cause injury. • Placing the stand on an unstable surface can be dangerous. Be sure to place it on a flat, firm surface. • This speaker system is magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker system is installed extremely close to the screen of a television set. If this happens, turn off the television, then turn it on again after 15 min to 30 min. If the problem persists, place the speaker system away from the television set. • Do not install your speakers overhead on the ceiling or wall. The grille is designed to be detachable, and as such it may fall and cause damage or personal injury if installed overhead. • Do not place heavy or large objects on top of the speaker. Doing so could provoke the speaker to fall, causing damages or bodily injury. PLACEMENT AND FINE TUNING For best results the speakers should be separated a distance approximately equal to the listening distance. Angling the speakers inward towards the listener will improve the image stability for non-central listeners. Close proximity to a side or rear wall will enhance the midbass performance, although too close (particularly a corner location) and the bass may be unnaturally high and image performance may be degraded. This speaker has "SIDE BASS". The placement of your speaker affects the quality of sound it produces. If you prefer normal stereo sound, set the "SIDE BASS" inside. If you prefer surround sound set the "SIDE BASS" outside. Caution Do not cover the "SIDE BASS" . Keep away from the audio rack or furniture. En 2 En STANDARD SURROUND SETUP This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound. MAKING AMPLIFIER SETTINGS Before connecting the speakers, please read the operating instructions supplied with your amplifier to select the speaker setting of amplifier : • FRONT SPEAKERS : LARGE CONNECTING YOUR SYSTEM Make sure all equipment is turned off before making any connections. • Correct wiring of your speakers is essential for achieving the best sound quality. Be careful to ensure proper polarity of connection. Connect to the speaker terminals on the rear of the amplifier. Connect the striped speaker cord to the red (+) terminal and the other cord to the black (–) terminal as shown below (for more details, refer to your amplifier instruction manual). After connecting the plugs, pull lightly on the cords to make sure that the ends of the cords are securely connected to the terminals. Poor connections can create noise and interruptions in the sound. Connect to the speaker terminals on the rear of the speakers. Unscrew the terminals on the speaker and insert the striped speaker cord into the red (+) terminal and the other cord into the black (–) terminal as shown below. SECURING THE FRONT SPEAKERS • Pass a commercially-available reinforced string through the plastic catch to securely support the speaker to the wall. Be sure that the wall to which you fasten the speaker is strong enough to support the weight of the speaker. After fastening the speaker, make sure that it does not fall over. • The speaker can incur damage in the event of a fall. • Do not attach the plastic catch directly to the wall. It should only be used in conjunction with reinforced string to prevent the speaker from falling. Pass and tie two reinforced strings through the plastic catches, and fasten the speaker to the wall as shown above. • If you are unsure of the quality and strength of the walls, consult a professional for advice. • Pioneer is not responsible for any accidents or damage that result from improper installation. Surround left Surround right Center Front left Listening position Front right Subwoofer (not supplied) CAUTION These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnectin...