Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 724.28 kb Dateiname: Unterrichtssprache:

4 Enter a new PIN, then press . 5 Enter the same PIN again to conrm. 6 Select [Con rm], then press OK. Change the brightness of the display panel 1 Press , select [Settings], and then press OK. 2 Select [Preference Setup] > [Display Panel], then press . 3 Select the brightness of the display panel, then press OK. • [100%] - Brightest • [70%] - Medium • [40%] - Dimmest Enable auto standby To save energy, you can automatically switch the home theater to standby after 30 minutes of inactivity (for example, in pause or stop mode). 1 Press , select [Settings], and then press OK. 2 Select [Preference Setup] > [Auto Standby], then press . 3 Select an option, then press OK. • [On] - Enable auto standby. • [Off ] - Disable auto standby. English EN 27 Turn the content menu on or off You can choose to skip or display the content menu for VCD and SVCD discs. 1 Press , select [Settings], and then press OK. 2 Select [Preference Setup] > [PBC], then press . 3 Select an option, then press OK. • [On] - Display the content menu when you inser t a VCD or SVCD. • [Off ] - Skip the content menu and play the disc from the rst title. Set a sleep timer You can switch the home theater to standby after a specic time. 1 Press , select [Settings], and then press OK. 2 Select [Preference Setup] > [Sleep Timer], then press . 3 Select an option, then press OK. • [Off ] – Disable the sleep timer. • [15 Minutes], [30 Minutes], [45 Minutes], [60 Minutes] – Select a delay. Set up EasyLink Your home theater suppor ts Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol.You can use a single remote control for HDMI CEC compliant devices that are connected through HDMI. Before you change the EasyLink settings, turn on the HDMI CEC operations for the TV and other connected devices. See the TV and device manuals for more information. Note • Philips does not guarantee 100% interoperability with all HDMI CEC compliant devices. Enable and disable EasyLink 1 Press , select [Settings], and then press OK. 2 Select [EasyLink Setup] > [EasyLink], then press . 3 Select an option, then press OK. • [On] - Enable EasyLink. • [Off ] - Disable EasyLink. Enable one-touch play Note • For T Vs that suppor t one-touch play. When you press , the T V and the home theater are turned on. If there is a disc in the home theater, the disc plays and the TV switches to the correct channel. 1 Press , select [Settings], and then press OK. 2 Select [EasyLink Setup] > [One Touch Play], then press . 3 Select an option, then press OK. • [On] - Enable one-touch play. • [Off ] - Disable one-touch play. 28 EN Enable one-touch standby When you press and hold (Standby) for at least three seconds, the connected HDMI CEC devices switch to standby. Note • When one-touch standby is turned off, the home theater cannot be switched to standby by a remote control from the TV or other devices. 1 Select [EasyLink Setup] > [One Touch Standby], then press . 2 Select an option, then press OK. • [On] - Enable one-touch standby. • [Off ] - Disable one-touch standby. Map audio from connected devices You can map your home theater to the audio output from connected devices. Note • The home theater must be connected to the devices by HDMI. • The connected devices must be turned on. 1 Press , select [Settings], and then press OK. 2 Select [EasyLink Setup] > [System Audio Control], then press . 3 Select [On], then press OK. 4 Read the on-screen instructions and select [Continue] to conrm scanning. » The home theater scans for devices and then displays a list of connected devices. 5 Select [Continue]. » A menu like the following is displayed. Aux2 Aux1 Aux3 Coaxial Optical Philips TV DVD player Recorder 6 Select a connected device on the left of the menu, then press . 7 Select the connector that is used for the device, then press OK. 8 Press , then repeat the previous two steps to map other connected devices. 9 Select [Finish] to exit. Update audio mapping from connected devices If you have already mapped audio from connected devices (see ‘Map audio from connected devices’ on page 29) , you can use this procedure to update your mapping. 1 Press , select [Settings], and then press OK. 2 Select [EasyLink Setup] > [Audio Input Mapping], then press OK. 3 Select a connected device, then press . 4 Select the connector that is used for the device, then press OK. 5 Press , then repeat the previous two steps to map other connected devices. 6 Select [Finish] to exit. English EN 29 Change advance settings Find the DivX VOD registration code for your home theater DivX Video-on-Demand (VOD) is a digital video delivery ser vice that allows you to download and buy video content from DivX content par tners. Your home theater has a DivX VOD registration code. Before you can buy video content, you must register your home theater on using the registration code. When you buy video content for your home theater, you can play it on this home theater only. 1 Press , select [Settings], ...

Herunterladen

Geben Sie zwei Ziffern: