Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
g AL1/AL2 • Set alarm. • View alarm settings. • Activate or deactivate alarm timer. h VOL +/ • Adjust volume. i MENU • Access iPod/iPhone menu. j PROG • Scan/store radio stations. k Source selection buttons: FM, AUDIO IN, DOCK • Select a source. l PRESET +/- • Select a preset radio station. • Scroll through the iPod/iPhone menu. m SLEEP • Set sleep timer. 3 Get started Always follow the instructions in this chapter in sequence. Install remote control battery Caution • Risk of explosion! Keep the batter y away from heat, sunshine or fire. Never discard the batter y in fire. • Danger of explosion if batter y is incorrectly replaced. Replace only with the same or equivalent type. • The batter y contains chemical substances, so it should be disposed of properly. • Perchlorate Material - special handling may apply. See Note • You can only use AC power as power supply.The pre- installed lithium CR2032 batter y can only back up time and alarm settings. For first-time use: Remove the protective tab to activate the batter y. EN To replace the battery a b Connect power Caution • Risk of product damage! Make sure that the power voltage corresponds to the voltage printed on the back or underside of the clock radio. • Risk of electric shock! When you unplug the AC adapter, always pull the plug from the socket. Never pull the cord. Set clock 1 In standby mode, press and hold SET TIME for two seconds to activate clock setting mode. » [12H] (12 hour) or [24H] (24 hour) blinks. 2 Press / to adjust the hour format. 3 Press SET TIME to confirm. » The hour digits blink. 4 Repeat steps 2-3 to set the hour and minute. » The set time is displayed. Note • When an iPod/iPhone is connected, the clock radio synchronizes time from the iPod/iPhone automatically. EN Turn on Press . » The clock radio switches to the last selected source. • To switch the clock radio to standby mode, press again. 4 Play from iPod/ iPhone You can enjoy audio from iPod/iPhone through this clock radio. Compatible iPod/iPhone The clock radio suppor ts these iPod and iPhone models: Made for. • iPod touch (5th generation) • iPod nano (7th generation) • iPhone 5 Listen to audio from iPod/ iPhone 1 Place the iPod/iPhone in the dock. EN 2 Press SOURCE repeatedly or DOCK on the remote control to select iPod/iPhone mode. 3 Play audio on the iPod/iPhone. • To pause or resume play, press . • To skip to a track, press / . • To search during play, press and hold / , then release to resume normal play. • To navigate the menu: press MENU, then press / to select, and press OK to confirm. To remove the iPod/iPhone: Pull the iPod/iPhone out of the dock. Charge the iPod/iPhone When the clock radio is connected to power, the docked iPod/iPhone star ts charging. Adjust volume You can adjust volume by pressing VOL +/repeatedly. 5 Listen to FM radio Tune to FM radio stations Tip • Position the antenna as far as possible from TV, VCR, or other radiation source. • For better reception, fully extend and adjust the position of the antenna. 1 Press SOURCE repeatedly or FM on the remote control to select FM tuner source. 2 Press and hold TUNING +/- for two seconds. » The clock radio tunes to a station with strong reception automatically. 3 Repeat step 2 to tune to more radio stations. To tune to a station manually: Press TUNING +/-repeatedly until you find optimal reception. Store FM radio stations automatically Note • You can store a maximum of 20 FM radio stations. In tuner mode, press an hold PROG for two seconds. » The clock radio stores all the available FM radio stations, and broadcasts the first available station automatically. EN Store FM radio stations manually 1 Tune to an FM radio station. 2 Press PROG. » The preset number begins to blink. 3 Press PRESET +/- repeatedly to select a number. 4 Press PROG again to confirm. 5 Repeat steps 1-4 to store other stations. Note • To remove a pre-stored station, store another station in its place. Select a preset radio station In tuner mode, press PRESET +/- repeatedly to select a preset radio station. 6 Other features Set alarm timer In standby mode, you can set two alarms to ring at different time. Note • Make sure that you have set the clock correctly. 1 Press and hold AL1/AL2 for two seconds to activate alarm setting mode. » The hour digits blink. 2 Press / repeatedly to adjust the hour. 3 Press AL1/AL2 to confirm. 4 Repeat steps 2-3 to set the minute and alarm volume. » The corresponding alarm icon is displayed. Select alarm source For alarm sound, you can select buzzer, your last listened radio chanel, or the latest played audio on your iPod/iPhone. EN Tip • If DOCK is selected as the alarm source, yet the audio cannot be played, buzzer will sound when alarm time comes. Activate/deactivate alarm timer 1 Press AL1/AL2 to view alarm settings. 2 Press AL1/AL2 again to activate or deactivate the alarm timer. » The alarm icon appears if alarm timer is on and disappears if it is off. • To stop ...