Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Connect the – terminals on both components using the other side of the cable. • Connect one speaker to the left (L) terminals of your amplifier, and another speaker to the right (R) terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. How to connect 1 Loosen the knob. 2 Twist the exposed wires of the cable together. Good No Good 10 mm 3 Insert the bare wire into the hole. 4 Tighten the knob and secure the cable. Test the firmness of the connection by pulling the cable lightly at the terminal. Notes • Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier. • Do not insert the insulation coating into the hole. The sound may not be produced. SPEAKERS A B LR ++ – – Loosen Insulation coating Bare wire NS-9900 (R) NS-9900 (L) Amplifier Speaker terminals of the amplifier Red (+) Black (–) Terminal hole Tighten When using a banana plug (China model only) 1 Unscrew the terminal knob. 3 Tighten the terminal knob. 2 Remove the cap by pulling it toward you. 4 Simply insert the banana plug into the terminal. Terminal 1 2 4 Banana plug 4 En REMOVING THE FRONT COVER SPECIFICATIONS English The front cover is fastened to the enclosure at six points and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the six holes on the inner surface of the cover with the six corresponding pegs on the speaker and push gently. Type .................................. 3-way bass reflex speaker system Magnetic shielding type Driver........................................... 16 cm cone type woofer x 2 13 cm cone type midrange 2.5 cm hard dome type tweeter Impedance ........................................................................ 6 . Frequency response .......................45 Hz to 35 kHz (–10 dB) to 100 kHz (–30 dB) Rated input power...........................................................50 W Maximum input power...................................................200 W Sensitivity ....................................................... 91 dB/2.83 V/m Crossover frequency .........................................800 Hz, 3 kHz Dimensions (W x H x D) Speaker cabinet..................................220 x 1157 x 335 mm Including stands..................................310 x 1170 x 371 mm Weight ......................................................................... 25.5 kg • Specifications are subject to change without notice due to product improvements. • Care should be taken not to exceed the input power values noted above. Taking care of the speaker When you wipe this unit, do not use chemical solvents (ex. alcohol or thinner etc.); this might damage the finish. Use a clean, dry cloth. For heavy dirt, dampen a soft cloth in the water, wring it out, and then clean this unit up with the cloth. Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools. This symbol mark is according to the EU directive 2002/96/EC. This symbol mark means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please act according to your local rules and do not dispose of your old products with your normal household waste. 5 En Limited Guarantee for European Economic Area (EEA) and Switzerland Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our website (or for U.K. resident). The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been discontinued or is considered uneconomic to repair. Conditions 1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the product may be returned at the customer’s expense. 2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland. 3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha. 4....