Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
All devices on a network must have an IP address. x LAN Abbreviation for Local Area Network. LAN is a general name for networks set up for communication among devices including computers, printers, and fax machines in relatively small areas such as offices or buildings. Others 31GB x x An encryption key used to limit the devices with which communication can occur. It is used to provide higher security for devices communicating via a wireless LAN router/ access point. x Proxy A program or a server that provides Internet access to computers within a firewall or quicker downloading of web pages. x Router A device that bridges networks, converting the protocols and addresses of each network. When connecting multiple network devices to the Internet, a router is necessary. The term “router” by itself may refer to any of these devices. x SSID Abbreviation for Service Set IDentifier. It is a name that identifies a particular access point within an IEEE 802.11 wireless LAN. To connect with an access point, a client device must be set with the same SSID. SSIDs can be up to 32 characters long. For higher security, a network key is normally also used. In this case, connection cannot occur unless the SSID matches the network key. x WEP Abbreviation for Wired Equivalent Privacy. An encryption key used in wireless LAN networks. As an IEEE standard based on RC4 algorithm cryptography, WEP is used to secure IEEE 802.11b wireless networks. During the transmission of a message between a wireless LAN access point and a client device, the sending side encrypts the data and the receiving side decrypts it. For communication to occur, both devices must use a common code key, which is called the “WEP key.” The encryption level is indicated by the bit count of the key; e.g., 64 bits or 128 bits. The higher the bit count, the higher the security level. x WPA Abbreviation for Wi-Fi Protected Access. An encryption standard for wireless LAN networks created by the Wi-Fi Alliance to remedy a number of serious security problems in the WEP system. In addition to the network name (SSID) and encryption key (WEP), this protocol uses a user authentication framework called “EAP” (Extensible Authentication Protocol) and a protocol called “TKIP” (Temporal Key Integrity Protocol) which automatically updates the encryption code at regular intervals for higher security. x WPA2 Abbreviation for Wi-Fi Protected Access 2. An encryption standard for wireless LAN networks. As an upgraded version of WPA created by the Wi-Fi Alliance, this standard uses AES (Advanced Encryption Standard) cryptography to provide stronger security than WPA. x WPS Abbreviation for Wi-Fi Protected Setup. A wireless network standard created by the Wi- Fi Alliance to allow you to set up a wireless network easily. A push button configuration method and a PIN code method are available. 32GB Troubleshooting Troubleshootingg If a problem occurs while operating the unit, follow the steps described below before consulting your nearest Sony dealer. If an error message appears, it is recommended that you make a note of its contents for reference. 1 Check to see if the problem is listed in this “Troubleshooting” section. 2 Check the following customer support site. • For customers in the USA • For customers in Europe You will find the latest support information and a FAQ at this web site. 3 If, after steps 1 and 2, you still cannot solve the problem, consult your nearest Sony dealer. If the problem persists after doing all of the above, consult your nearest Sony dealer. When bringing the product in for repairs, be sure to bring in the entire system (main unit, remote control, AC adaptor, and AC power cord). This product is a system product, and so the entire system is needed to determine the section requiring repair. Power The unit does not turn on. • Make sure the AC adaptor and AC power cord are connected correctly. • Make sure the power switch is set to ON. • Set the power switch to OFF, and then set it to ON again. The NETWORK STANDBY indicator remains lit for a while after you set the power switch to ON. • It takes about 20 seconds for the unit to turn on. The unit remains warm after the power is turned off. • When the unit is in the network standby mode, some parts of the internal system remain active. Slide the power switch to OFF to limit the power consumption to a minimum, however, the unit cannot be operated by a controller in such a case. The unit turns on and starts playback automatically. • The unit can be controlled by a controller. If the unit receives an order to play the audio content on the server while it is in the network standby mode, it turns on and starts playback automatically. To enter the network standby mode again, press the ?/1 (power) button on the remote. To prevent the unit from automatically turning on, slide the power switch to OFF. The unit turns off automatically. • The unit enters the networ...