Stimmen - 5, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Atlantic Technology Dateigröße: 284.24 kb Dateiname: Unterrichtssprache:

Fotos und technische Daten  Atlantic Technology  4400 C

About one-third of the way out from the corners in most rooms is a good starting point. If you areusing a THX Ultra 2 certified controller/receiver,you should place the back surround speakers approximately 1 to 2 feet (.3,.6m) apart in the center of the back wall. The special circuitry in the processor will help to create a believable and effective surround field using this placement. Please read the electronics manual to learn more about this placement option. Speaker Placement Instruction Manual Speaker Placement Front Speaker Array should be placed as close to ear level as possible. Generally, the farther away the speakers are from the walls, the better they will sound. Subwoofer placement is Left Center Right dependent on room size and shape. Experiment to find a location that produces the Surround Speakers smoothest response. should be placed directly to the sides of the seating area and approximately Subwoofer 3 feet (1 meter) above the listener’s ear level. Left Right Surround Surround Left Right Surround Surround Back Back Surround Back Speakers should be placed approximately 3 feet (1 meter) above the listener’s ear level and 30 off the center axis. Direct radiators may be used here. Connecting Your System System 4400 High Performance Loudspeakers Stereo Systems If you are setting up a stereo system using a pair of 4400 LR’s with subwoofer(s), begin with these general guidelines: . The distance between the speakers should be approximately one-half their distance from the prime listening position. . If you point the front of the speakers directly towards the prime listening position(“toe”themin),youwillachievethemostpreciseimagingand the most direct high frequency sound.If you have a “bright”or “hard” sounding room,aimingthespeakers straight out into the room(or just aiming them partially towards you) may make for a more natural and pleasing sonic balance. . For the smoothest upper bass/lower midrange response, the distance from each speaker to its three closest room surfaces should be different. . In most rooms, you should not place your speakers in the corners. . Try to keep the speakers at least 2 feet (.6m) from the back and side walls. The goal is to reproduce the most accurate musical timbre and the most convincing natural sound.Additionally, a well set-up stereo pair of speakers will create excellent imaging and a cohesive representation of the soundstage. Placement in the room and your listening position has an enormous impacton the ultimatesoundyouwillachievefromyoursystem.Themost important thing is to be creative! Try placing your speakers on the long wall instead of the short one. Toe the speakers in or point them straight ahead. Pull them away from the wall or push them closer.Don’t be timid.You’ll find that moving your speakers, even a few inches, can dramatically change and possibly improve their sound. Connecting Your System We recommend that you connect your system using high quality dual conductor stranded wire of 16 gauge or heavier, for lengths up to 25 feet (8m) . (Remember, the lower the gauge number, the heavier the wire). Use heavier gauge wire for longer runs. Please contact your audio/video dealer or installer for specific cable recommendations and further information regarding special circumstances. The terminals themselves are designed to allow the use of very heavy speaker wire or connectors. Be sure to tighten them securely, but don’t over-tighten them. WARNING: To prevent risk of electrical shock or damage to your equipment, always switch off the amplifier or receiver when making any system connections. You can connect your speakers by using a variety of audio connectors such as banana plugs (single or double), pin connectors, spade lugs, etc., or you can: 1. Remove .” (13mm) of insulation from each wire end. 2. Twist the stranded wire together, keeping the two ends separate. 3. Place the appropriate wire through the postholes in the connectors. These holes are revealed when you loosen the connector’s capscrew. 4. Screw down the capscrew tightly, but be careful not to over tighten it. 5. Check the tightness of the capscrews 24 hours after hookup and occasionally after that, as they can loosen over time. We recommend that you check your local electrical codes to make sure that you are not using improper connectors. It’s important to observe polarity while making speaker connections: red (+) terminals on the amplifier to red (+) on the speaker, black (–) on the amplifier to black (–) on the speaker. Look carefully at the wires you are using and note that one of the conductors of each pair will typically be identified by color, printing on the outer jacket, ridgesonthe outerjacket,ora threadintertwinedwith the wirestrands.By convention, the marked wire is connected to the red (+) terminal.Whether you are connecting a complete system, or adding a single speaker component to your present system, the wiring should look like the system wiring diagrams on the opposite page WARN...

Herunterladen

Geben Sie zwei Ziffern: