Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Atlas Sound Dateigröße: 270.29 kb Dateiname: Unterrichtssprache:

When re-attaching speaker to bracket be sure to tightly secure speaker mounting bolts. Thread locking compound should also be used in this operation. 1. Choose the bracket mounting holes best suited for the surface you are mounting to. For best stability the 5.8" (16mm) diameter outer keyhole slots are recommended. 2. When using these mounting holes 1.2" (grade 5 hardware minimum) hardware should be used with proper flat and lock washers. Remember to use thread- locking compound on all parts. 3. Use the dimensions noted on the illustration to mark the points where the starting hole should be drilled. 4. Choose appropriately sized bit and drill holes. 5. Attach speaker bracket, using bolt, flat washer, and lock washer as shown and re-attach loudspeaker to bracket. 6. Secondary (safety) suspension point: Use a load rated cable or steel chain (capable of holding the speaker should it come loose from the primary mounting point). This cable or chain assembly should be attached to at least (2) of the drop forge eyebolts provided on the AH speaker and secured to the mounting surface via approved, load rated hardware. Specifications are subject to change without notice AtlasSound.com 1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435 ©2006 ATLAS SOUND LP Printed in U.S.A. 000606 ATS002386 RevA 6/06 PP BOTTOMVIEW5“7.83“1.210“0.55“7.2 INSTALLATION INSTRUCTIONSAH SERIES LOUDSPEAKERS 8", 12", AND 15" INSTALLATION INSTRUCTIONSAH SERIES LOUDSPEAKERS 8", 12", AND 15" SUSPENDED INSTALLATION VIA EYEBOLTS (INCLUDED) Using 1.4" Diameter Wire Rope Note: Use of 1.4" load rated wire rope is suggested to provide a static working load limit of 1400lbs (635kg) and moving load limit of 875lbs (397kg) per point. 1.8" cable is not recommended as load limits are reduced to 400lbs (181kg) static, and 250lbs (113kg) moving. Considerations for overhead suspension using AH Series eyebolts and wire rope: 1. Always apply the load to the eye in the plane of the eye. 2. Always use shoulder eyebolts for angular lifts. 3. Always tighten eyebolts securely against the load. 4. Apply first load to test the assembly. This load should be of equal or greater weight than the loads expected in use. 5. Use wire rope compression fittings & thimbles whenever possible and prepare terminations only as instructed by the manufacturer. 6. If wire rope clips are used, check and retighten to the manufacturer's recommended torque. Eyebolt Working Load Limits 1.4" Shank (Provided with AH Series) 90° angle: 650lbs (295kg) 60° angle: 420lbs (191kg) 45° angle: 195lbs (88kg) Less than 45° angle: 160lbs (73kg) LESS THAN 45 DEGREE ANGLE 45° 60° 90° 0 ANGLE Specifications are subject to change without notice AtlasSound.com 1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435 ©2006 ATLAS SOUND LP Printed in U.S.A. 000606 ATS002386 RevA 6/06 PP INSTALLATION INSTRUCTIONSAH SERIES LOUDSPEAKERS 8", 12", AND 15" INSTALLATION INSTRUCTIONSAH SERIES LOUDSPEAKERS 8", 12", AND 15" SPEAKER CABLE RECOMMENDATIONS AND CONNECTION INSTRUCTIONS Wire Gauges (8 Ohm operation) For very short distance speaker cable runs (less than 25') #16-gauge, stranded, twisted pair speaker cable may be used. For speaker cable runs between 25' and 75', #14-gauge, stranded, twisted pair speaker cable is recommended. For speaker cable runs greater than 75', #12-gauge, stranded, twisted pair speaker cabl...

Herunterladen

Geben Sie zwei Ziffern: