Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
The power connection uses an I.E.C. type connector, use only the supplied polarized AC power cord. Use only a power cord that matches this type of connection. Be sure to only connect this unit to a power outlet that matches the printed power label on the unit. Never use a power when the ground prong has been removed or broken off. The ground prong is used to reduce the risk of electrical shock in case of an electrical short. This cord is designed to fit in one direction only. Do not attempt to force a cord if it does not fit, be sure the cord is being inserted properly. 13. FUSE HOLDER – This housing stores the 10 amp GMA protective fuse. Always replace with the exact same type fuse, unless otherwise instructed, by an authorized American Audio® service technician. Replacing with any other type of fuse than that of the recommended fuse will void your unit warranty. 14. PROTECT INDICATOR - The red Protect LED will begin to glow when the channel goes into protect mode. When the channel goes into protect mode all output for that channel will turn off. This is to protect any speakers connected to the channel. 15. MAIN POWER SWITCH – This is the main power ON/OFF button. A yellow LED directly above the power switch will glow indicating power is ON. Before main power is applied, be sure you have made all connections to the speaker. Remember to avoid damaging pops to the speakers, the mixer is turned on first and turned off last. 16. VOLTAGE SELECTOR SWITCH -Because power supplies vary from location to location a voltage selector switch has been incorporated in the unit's design. This switch can select a voltage input of 120v or 230v to accommodate the two major power source. Always be sure to disconnect the power plug before changing the voltage. 17. CLIP L.E.D. - When your Subwoofer or Speaker Levels are distorted or too loud this L.E.D. will light letting you know to adjust your volume level to a lower setting. ©American Audio® --Tri Pack System -Instruction Manual Page 7 Tri Pack System Controls and Features Tri Pack System Controls and Features 18. TRANSPORT HANDLE – The Tri Pack System with built-in heavy- duty transportation han- dle. Be sure to carry the speaker by the handle for secure and easy transportation. 19. SPEAKON CONNECTIONS – The speaker includes a pair of Speakon type connections. You may use both connections at once to loop speakers. These Be sure to use either the Speakon type input connector or the 1/4” Phono input connector, never use more than one input connection at once. The Speakon connectors have a pin 1+ (hot) and 1- (ground) configuration, pins 2+ and 2- are not used. For more wiring information regarding the Speakon connectors see page 17. 20. RUBBER FEET – The speaker includes heavy-duty rubber feet on the bottom of the unit. These feet are used to secure a speaker to another when stacking. They are also used to secure the speaker to the ground to prevent it from shifting during heavy bass reproduction. ©American Audio® --Tri Pack System -Instruction Manual Page 8 AUX 4 AUX / IN MADE IN CHINA MODEL NO.: Q-3433 MKII POWER SOURCE: 115/230V~ 50/60Hz 20W MIN MAX TRIM OUTPUT ©American Audio® - - Tri Pack System - Instruction Manual Page 9 Tri Pack System Set-Up Tri Pack System Set-Up XLR-XLR Balanced Cables RIGHT SATELLITE SPEAKER LEFT SATELLITE SPEAKER SUBWOOFER AUX 4 AUX / IN MADE IN CHINA MODEL NO.: Q-3433 MKII POWER SOURCE: 115/230V~ 50/60Hz 20W MIN MAX TRIM OUTPUT Tri Pack System Set-Up Tri Pack System Set-Up ©American Audio® - - Tri Pack System - Instruction Manual Page 10 XLR-XLR Balanced Cables RIGHT SATELLITE SPEAKER LEFT SATELLITE SPEAKER SUBWOOFER DLS 15P DLS 15P Tri Pack System Satellite Mounting Tri Pack System Satellite Mounting Pole Mounting – The Impact 3 satellite speakers include a pole mount option. The pole mount socket located on the bottom of the speaker may be used to secure the speaker to a speaker tri-pod, such as the American Audio® SPS-1B as illustrated on the left. Always be sure to follow the guidelines listed below when pole mounting your speaker; • Always be sure the stand is designed to support the weight of the speaker • In outdoor situations that are prone to windy conditions and strong wind gust, be sure to use sandbags as additional tri-pod support, this will greatly reduce the risk of tipping • Do not stack speakers on top of each other when mounting on a tri-pod. Only one speaker should be mounted to a tri-pod at one time. • Always position the tri-pod legs away from foot traffic • Extend the tri-pod legs to their fully extended position to avoid accidental tipping • Observe and follow all safety guidelines and regulations specified by the tri-pod’s manufacturer • Be sure the tri-pod is situated on a flat, level, and stable surface • Always tighten all tri-pod locks ©American Audio® --Tri Pack System -Instruction Manual Page 11 Tri Pack System Spe...