Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2. Whats in the Box? 1. SW225 Voice Projector 2. S1204 Wireless Speaker 3. S1670 Wireless Transmitter with connecting cable 4. Two S1090 Tripods 5. Rolling Case 6. Wireless headset and lapel mic with transmitter 7. Computer Interface Cables 4. 4. 6. 5. 7. stereo cable projector cable Headset & lapel w/ transmitter Made in USA Thank you for choosing the SW227 Voice Projector with Wireless Powered Speakers Kit from AmpliVox Portable Sound Systems. Our system combines flexibility with functionality. Please refer to this user guide as you enjoy the unique capabilities of another quality product from AmpliVox Portable Sound Systems. As always, you can reach us at 800-267-5486, or at 847-489-9000, Monday - Friday 8am - 6pm CST. user guide TABLE OF CONTENTS..........................................................1 battery installation / set up...................................2 control panel layout..................................................3 wireless mic setup.......................................................3 problem solving ...........................................................4 SW227 2 BATTERY installation / SET-UP: Install Power supply in all componenets: important! Do not mix battery types or attempt to recharge alkaline batteries. Equipment dammage, safety hazard or fire could result. Remove batteries if the unit is not going to be used for long periods of time to prevent leakage. SW225 Wireless Voice Projector: Runs on AC power or battery power. The battery carriage holds 10 D-cell alkaline batteries or our S1465 NiCad battery pack (requires S1460 AC adapter to recharge). Or run on a 12 Volt DC adapter (automotive cigarette lighter plug-in, not included). S1204-70 Wireless Powered Speaker: Runs on AC power or battery power. The battery carriage holds 10 D-cell alkaline batteries or our S1465 NiCad battery pack (requires S1460 AC adapter to recharge). Or run on a 12 Volt DC adapter (automotive cigarette lighter plug-in, not included). For both the 1204-70 and SW225: Loosen four thumbscrews and remove battery door from back of speaker. Remove battery carriage. Insert 10 D-cell alkaline batteries, observing polarity, or replace with fully charged S1465 NiCad battery pack. Carefully replace the battery carriage. Reposition battery door and fasten the thumbscrews. S1670 Transmitter Power Supply: Requires one 9-Volt battery or a 9-Volt AC adapter (not supplied). Remove battery door on back of transmitter. insert one new 9 volt alkaline battery, observing polarity, and replace the door. Lapel & Headset Mic Battery Installation: Requires one 9-Volt battery or a 9-Volt AC adapter (not supplied). Remove battery door on back of transmitter. insert one new 9 volt alkaline battery, observing polarity, and replace the door. set-up wireless transmitter for the S1204-70 speaker: PLEASE NOTE: YOU HAVE TWO SEPERATE TRANSMITTERS. ONE IS FOR THE SPEAKER AND THE OTHER IS FOR THE MICROPHONE. SPEAKER = BEGINS WITH 169 MIC = BEGINS WITH 171 Connect provided cable from the MIC INPUT JACK on the S1670 transmitter (labled 169) into the LINE OUT JACK (*see image on next page) on the Amplifier on the SW225 Voice Projector. Turn SW225 Amplifier ON. Turn S1670 transmitter ON. Make sure frequencies MATCH. Turn S1204-70 Speaker Amplifier ON. The red light should illuminate. NOTE: If for any reason the S1670 transmitter frequency is changed from its factory set position A please reset to A. The internal wireless receiver is preset to A. NOTE: The frequencies used by the S1204-70 Speaker and the S1670 transmitter are not on clear channels adn may be used by other devices. If the unit receives interference and if you are unable to use the S1670 transmitter, connect the LINE OUT on the SW225 Voice Projector to the S1204-70 LINE IN using a 3.5mm miniplug cable. Turn the volume control on the S1204-70 speaker completely down. SW225 Wireless Mic Set up: Plug headset or lapel microphone into transmitter labled with 171, select A or B frequency, turn power switch ON. A red light should come on. Turn SW225 on with the main power switch. When the power switch is in the ON position, the red light will be on. Turn wireless receiver power switch on and select matching frequency to the mic transmitter, SW225 Voice Projector s1204-70 WIRLESS POWERED SPEAKER S1670 TRANSMITTER WITH CABLE BATTERY DOOR PANEL AMPLIFIER CONTROL PANEL HANDLE transmitter battery installation PLEASE NOTE: YOU HAVE TWO SEPERATE TRANSMITTERS ONE IS FOR THE SPEAKER AND THE OTHER IS FOR THE MICROPHONE. SPEAKER = 169 MIC = 171 RIBBON FOR BATTERY REMOVAL 9V DC ALKALINE BATTERY HANDLE AMPLIFIER CONTROL PANEL BATTERY DOOR PANEL BATTERY COVER either A or B. Both the microphone transmitter and the amplifier have to be on the same frequency for the wireless mic to work proplerly. If you encounter interference, switch frequencies. Rotate VOLUME control knob on the amplifier to obtain desired loudness level throughout the coverage area. The microphone has an ON/OFF switch. i...