Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If the burner does not ignite with the valve open, gas will continue to flow out of theburner and could accidently ignite with risk of injury. Turn controls and gas source or tank OFF when notin use. WARNINGMatch-Lighting sDo not lean over grill while lighting. 1. Turn all burner control valves. Open lid duringlighting. Turn on gas at LP cylinder. 2. Place lit match into match holder, then into side of grill bottom (as shown below). 3. Push in and turn IGNITION BURNER knob to PRE-HEAT. Be sure burner lights and stays lit. 4. To ignite right burner, turn right knob to PRE-HEAT. After Lighting: Turn knobs to HI for warm-up. Burner Flame Check • Light burner, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Always check flame prior to each use. If only low flame is seen refer to"Sudden drop or low flame" in the Troubleshooting Section. HI LO Hose Check • Before each use, check to see if hoses are cut, worn or kinked. Replace damaged hoses before using grill. Use only valve/hose/regulator specified in the Parts List. Normal Kinked Hose Hose Turning Grill Off • Turn all knobs to OFF position. Turn LP tank off by turning OPD hand wheel clockwise to a full stop. Ignitor Check • Turn gas off at LP tank. Press and hold ignitor button. "Click" should be heard and spark seen each time between collectorbox or burner and electrodes. See "Troubleshooting" if no click or spark. Valve Check • Important: Make sure gas is off at LP tank before checkingvalves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobsdo not spring back, replace valve assembly before using grill. Turn knobs to LO position then turn back to OFF position. Valves should turn smoothly. CAUTION SPIDER ALERT! GAS COLLECTOR BOX & IGNITOR VALVE CONTROL PANEL BURNER VENTURI LIFT OUT BURNER ASSEMBLY AIR SHUTTER SPIDER WEBS INSIDE VENTURI SPIDER WEBS INSIDE VENTURICLEAN OUT VENTURI REMOVE BURNER CLIPS If you notice that your grill is getting hard to light or that the flame isn’t as strong as it should be, take the time to check and clean the venturis. In some areas of the country, spiders or small insects have been known to create “flashback” problems. The spiders spin webs, build nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of gas to the burner. The backed-up gas can ignite in the venturi behind the control panel. This is known as a flashback and it can damage your grill and even cause injury. To prevent flashbacks and ensure good performance the burner and venturi assembly should be removed from the grill and cleaned before use whenever the grill has been idle for an extended period. CAUTION SPIDER ALERT! GAS COLLECTOR BOX & IGNITOR VALVE CONTROL PANEL BURNER VENTURI LIFT OUT BURNER ASSEMBLY AIR SHUTTER SPIDER WEBS INSIDE VENTURI SPIDER WEBS INSIDE VENTURICLEAN OUT VENTURI REMOVE BURNER CLIPS If you notice that your grill is getting hard to light or that the flame isn’t as strong as it should be, take the time to check and clean the venturis. In some areas of the country, spiders or small insects have been known to create “flashback” problems. The spiders spin webs, build nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of gas to the burner. The backed-up gas can ignite in the venturi behind the control panel. This is known as a flashback and it can damage your grill and even cause injury. To prevent flashbacks and ensure good performance the burner and venturi assembly should be removed from the grill and cleaned before use whenever the grill has been idle for an extended period. Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grate and heat tent. 3. Under grill remove grease cup, disconnect ignitor wire from burner. 4. Inside grill remove burner assembly (A), clean ceramicportion of electrode with rubbing alcohol and a swab. 5. Clean outside of burner with soap and water. Lay burner upside down on flat surface, insert garden hose to force water through tubes. Make sure water comes out of all burner holes. Open clogged holes with a thin wire. Shakeout excess water and examine holes. Due to normal wear and corrosion some holes may become enlarged. If any large cracks or holes are found replace burner. 6. If grill is to be stored, coat burner lightly with cooking oil. Wrap in protective cover to keep insects out. 7. If not storing grill after cleaning, replace burner into grill bottom. VERY IMPORTANT: Burner tubes must re-engage valveopenings. See illustration (A). 8. Reattach ignitor wire to electrode. 9. Reposition heat tent and cooking grate. Reattach clean grease cup to grease clip. 10. Before cooking again on grill, perform a “Leak Test” and “Burner Flame Check”. A Valve Correct burner-to-valve engagement Burner Tube B LIMITED WARRANTY – REV...