Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
However, the method of assembly remains the same. PARTS DIAGRAM PARTS DIAGRAM SEFQDBALLIYZLCKBBJJGGHHDDIIFFEEKKCCNOXTMMUNNOORRPPWVBGHJMPRSSSTTAAKKQQSSTTUUVV ASSEMBLYASSEMBLY 1 Attach the two locking casters at the rear of the bottom shelf and the two Fixed casters at the front. Use the provided caster wrench to fully tighten casters. Locking caster Bottom shelf Fixed caster RearFront 2 Attach cart frames to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel.1/4-20x1/2” screw IMPORTANT: Panel with large hole must be on left side of bottom shelf. 7mm flat washer 7mm lock washer Left cart frame (with large hole) Make sure cart frames are pushed as far to therear of bottom shelf as possible before fully tightening screws. Right cart frame 33 Attach front brace to cart frames using two #10-24x1/2” screws, 5mm lock washers and 5mm flat washers on each side. RearMagnet #10-24x1/2" screws 5mm flat washers 5mm lock washers 4 Attach rear cart brace to cart frames using two #10-24x1/2” screws, 5mm lock washers and 5mm flat washers on each side. 55 Insert wire ends on lower tank exclusion wire into bottom shelf (A). Attach with two #8-32x3/8" screws diagonally. Place upper tank exclusion wire on front brace and back brace as shown, secure with two #8-32x3/8" screws and #8-32 flange nuts (B). Magnet Front brace #8-32x3/8" screw #8-32 flange nutUpper tankexclusion wire Lower tank exclusion wire 6 Slid the door hinges onto the screw with arrow direction as indicated. Secure the door with all six #8-32x3/8" machine screws (A). Screw two #8-32x3/8" machine screws in the cart side panel (B). B#8-32x3/8” machine screws This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Insert 1/4-20x1/2" screws through side panels and firebox in all four corners. Secure with fiber washers and 1/4-20 flange nuts. 1/4-20x1/2" screw Fiber washer 1/4-20 flange nut Mount fascia onto side shelf using three #10-24x1/2" screws, 5mm lock washersand 5mm flat washers (A). Hang side shelf on the tabs mounted on the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiberwashers and 1/4-20 flange nuts on each bracket (B). Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (C). CAUTION SHARP EDGES! Wear gloves if necessary CRepeat on front bracket 1/4-20x1/2" screw 1/4-20 flange nut Fiber washer Lock washer Flat washer #10-24x1/2" screw Repeat on left side shelf Flat washer Lock washer 1/4-20x1/2" screw Side shelfHook side shelf into inside edge Repeat step 7 (A) on left side shelf. Hang sideburner shelf on the tabs mounted on the firebox. Attach shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiber washers and 1/4-20 flange nuts on each bracket (A). Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers. Place drip pan on the sideburner shelf with four #8x3/8" self-tap screws and 5mm fiber washers (B). CAUTIONSHARP EDGES! Wear gloves if necessary Repeat bracket screws on front leg 1/4-20x1/2" screw 7mm fiber washers #8x3/8" self-tap screw 5mm fiber washers Sideburner shelf assembly Lock washer First, remove the two screws from the sideburner valve bracket. Align sideburner valve bracket behind sideburner shelf fascia with bezel on same level. Secure them altogether with two #8-32x3/8" screws. Press sideburner control knob onto valve stem. Control Knob Bezel Control KnobSideburner Valve Bracket 1111 Insert sideburner burner into sideburner drip pan (A), making sure burner tube engages sideburner valve. See illustration (B) for proper burner-to-valve engagement. Center stud on bottom of burner fits into center hole in sideburner drip pan. Secure burner to drip pan with one wing nut (C). Finally connect sideburner ignitor wire to sideburner electrode. Burner tube Valve Sideburner Ignitor Wire Sideburner Burner Wing Nut 12 12 Attach and fully secure hinges to lid with four #8-32x3/8" screws, #8-32 flange nuts first. Place sideburner lid onto left side shelf and align hinges to holes on side shelf top. Attach sideburner lid assembly to side shelf using four #8-32x3/8" screws, #8-32 flange nuts. Sideburner Lid #8-32x3/8" screw #8-32 flange nut Place sideburner cooking grate in drip pan. Sideburner Cooking Grate Place four flame tamers over burners by inserting tabs into slots in front offirebox. Opposite ends of flame tamers rest on pins in back of firebox. Backof firebox Flame tamer Front of firebox Flame tamer Place cooking grates into grill bottom. Cooking Grates To assemble Swing Away, first insert pivot wire into holes in Pivot wire side of grill lid. Second, insert leg wires into holes in sidesof grill bottom. Grate wires running front to back should be facing upward side to side wires downward. Swing Away 1717 Hang grease cup wire from bottom of firebox andplace gre...